VeEX VePAL TX300 Скачать руководство пользователя страница 72

Страница: 72 / 421

6.7 Measurement Configuration

Tapping the

Measurements

tab opens the setup screen for the Timer, Performance Analysis, and General configurations.

Measurements tab

Go back to top

Go back to TOC

6.7.1 Timer Setup

Configure a test to run for a fixed duration or a delayed start.

Mode

: Manual, Timed, and Auto selections are available

Manual:

This is linked to the Start/Stop function on the drop-down menu

Timed:

The test duration can be set by the user. The test duration can be set in seconds, minutes, hours or days. The test

is activated by the Start/Stop function on the drop-down menu

Auto:

A predetermined start time can be set by the user. The test duration can be set in seconds, minutes, hours or days.

After programming the start time and duration, press the

Start

button on the drop-down menu and the test will be

activated automatically when the programmed start time is reached.

Note:

The timed mode will be required when running a M.2100 or M.2101 performance objective.

Go back to top

Go back to TOC

6.7.2 Performance Analysis

The Analysis setup page selects the ITU-T performance test that will be performed by the unit. Depending on Test mode, the

selections include None, G.821, G.826, G.828, G.829, M.2100, and M.2101.

Analysis

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды