VeEX VePAL TX300 Скачать руководство пользователя страница 163

Страница: 163 / 421

Editing of J1, C2, H4, G1, Z5, and J2, V5, Z6 is permitted as follows:

Hexadecimal value using pop-up keypad.

Binary values using simple on-screen bit toggle or pop-up keypad.

Convenient drop-down selections. In some instances, the drop-down options will be available over multiple

pages.

C2 Byte from POH

Overhead Generator

Programming most overhead bytes is possible using the OH Generator feature, however dedicated

test functions are available for Pointer Tasks, Payload Labels, Trace Identifier, APS Testing, TCM

testing.

In some instances, more advanced editing is possible using the dedicated functions.

Go back to top

Go back to TOC

10.1.4 Pointer Tasks

Tap the Pointer Tasks icon to display the Pointer testing screens.

SDH/SONET Tools Menu

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды