VeEX VePAL TX300 Скачать руководство пользователя страница 224

Страница: 224 / 421

HOLD

: Call Hold - the user may interrupt a call, then reestablish it later. Interruption frees the associated B-channel.

UUS

: User to User Signaling - allows a user to send an Information message in the Setup, Alerting, or Connect message

on the D-channel, without connecting the call; the message shows on the ISDN phone display.

: Terminal Portability; the ability to suspend and reconnect a call; for example, to move a phone from one plug to

another.

AOC-D/E/S

: Advice of Charge - Determines when charging information is available to the served user; during the call,

when the call is terminated, when the call is established.

MCID

: Malicious Call Identification - the called party, on a per call basis, requests the network to register the called party

phone number, the calling party number, and the date and time of the calls.

: Call Waiting - informs a user of an incoming call which has no B-ch available; user may accept, reject, or ignore.

CUG

: Closed User Group; a private network which restricts communication between members and nonmembers.

Go back to top

Go back to TOC

11.7.1.7 Multi Call

Multi Call mode is used to place multiple calls in sequence or in parallel. Setup parameters are described below:

Page 1

Type:

Single Number or Number Script

Mode:

Parallel or Sequential calling

See

11.7.1.3 Call - Voice and 3.1K Audio Setup

for descriptions of other parameters on Page 1.

Multi Call Setup (Page 1)

Page 2

Page 2 lists call settings, including:

Ring Wait (sec)

Call duration (sec)

Number of the starting and stopping B Channel

Number of the starting and stopping B Channel line

Configure these options by tapping on the corresponding box.

Multi Call Setup (Page 2)

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды