VeEX VePAL TX300 Скачать руководство пользователя

Страница: 210 / 421

10.2.10 Round Trip Delay

Round Trip Delay Results

The Round Trip Delay (Propagation Delay) measurement works by sending a test pattern. A errors is transmitted in the pattern.

The time it takes for the error to reach the receiver is the propagation time through the network.

Select SONET as TX/RX standard.

View the Round Trip Delay of a looped back signal.

Set check box on Setup RX pattern to Out-of-Service.

Go back to top

Go back to TOC

10.2.11 Jitter and Wander

For more information on Jitter and Wander, please see

13.0 Jitter and Wander Application

Go back to top

Go back to TOC

10.2.12 V-SCAN

For more information on V-SCAN, please see

10.1.12 V-SCAN

Go back to top

Go back to TOC

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды