VeEX VePAL TX300 Скачать руководство пользователя страница 176

Страница: 176 / 421

Go back to top

Go back to TOC

10.1.11 Jitter and Wander

For more information on Jitter and Wander, please see

13.0 Jitter and Wander Application

Go back to top

Go back to TOC

10.1.12 V-SCAN

The V-SCAN function allows users to monitor the health or status of individual channels/tributaries in a real-life mixed-payload

OTU2, SDH or SONET signals.

First, configure the test set to match the optical interface type and rate (for example, OTN, SDH or SONET). Supported rates are

OTU2, STM-64, STM-16, STM-4, STM-1, OC-48, OC-12, and OC-3. Note that some hardware configurations may not support

the lower rates (STM-16, STM-4, STM-1, OC-48, OC-12, and OC-3) and the test set will show a warning message that “V-

SCAN does not apply to the current configuration.”

Connect the test set’s receiver to a monitoring point and verify that the signal LED is green and that the received signal is within

the receiver’s range. Avoid marginal signals or saturation as they may induce errors that are not necessarily present in the line

under test.

Accessing the V-SCAN function

On the North American version of the TX300 series test sets:

For SONET or SDH signals:

Home

(Main Menu) >

Advanced Mode

SONET/SDH Tools

More

V-SCAN

For OTN signals:

Home

(Main Menu) >

Advanced Mode

OTN Tools

V-SCAN

On the International version of the TX300 series test sets (TX300e):

For SDH or SONET signals:

Home

(Main Menu) >

SONET/SDH Tools

More

V-SCAN

For OTN signals:

Home

(Main Menu) >

OTN Tools

V-SCAN

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды