manualshive.com logo in svg

VeEX VePAL TX300, Руководство пользователя, Страница: 75 / 421

Поделиться
Скачать
VeEX VePAL TX300 Скачать руководство пользователя страница 75

Auto-config tab

The 

Auto-Config

 function automatically sets the receiver of the test set. A search for SDH and PDH signals at both the electrical

or optical inputs is performed to determine the signal structure. For electrical signals, both Terminated and PMP voltage ranges

are searched and supported.

Procedure

Tap on the 

Start

 button 

 to begin the search. The received signal is checked for network type, hierarchy and bit

rate, payload structure, payload framing, test pattern and signal level. If the search is successful, a “PASS” result is displayed.

Search parameters and criteria

Interface:

 Checks physical parameters (bit rate line code).

Mapping:

 Checks mapping structure using the signal label and pointer bytes.

Payload:

 Only test patterns defined in ITU-T or ANSI standards will be recognized. If no test pattern is detected, the unit

assumes live traffic.

PDH Signals:

 Unframed or framed payloads at all hierarchies. For 1.5M signals containing 64kbps timeslots, the TX300/e will

assume live traffic and will not search for a test pattern.

Go back to top

 

Go back to TOC

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Отзывы:

Нет отзывов