VeEX VePAL TX300 Скачать руководство пользователя страница 386

Страница: 386 / 421

FC-2:

Only FC-2 frames have a header, so these fields are not available for FC-1 frames.

Defines the framing rules and mechanisms for controlling the different service classes. The following building blocks are

defined by the standard:

Ordered Set

Frame

Sequence

Exchange

Protocol

FC-2 Frame Structure

FC-2 Header

The FC-2 header is only 24 bytes long. Header settings do not affect the transmission or reception

of the FC-2 frame.

Go back to top

Go back to TOC

Understanding the Basic Test Channel Frame Structure

The Fibre Channel standard defines a variable frame length consisting of 36 bytes of overhead and up to 2112 bytes of payload for a

total maximum size of 2148 bytes.

SOF and EOF

A Start of Frame (SOF) delimiter and End of Frame (EOF) delimiter mark the beginning and end of each Fibre Channel

frame

Available for both FC-1 and FC-2 frame formats

Frame Header

Is the first field of the frame content and immediately follows the SOF delimiter and is transmitted on a word boundary

Is used to control link operations and device protocol transfers as well as detect missing or out of order frames

Available in FC-2 frame format only

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды