VeEX VePAL TX300 Скачать руководство пользователя

Страница: 256 / 421

PRBS Pattern:

Use the pattern drop-down box to select the test pattern which will be inserted into the transmitted signal.

Pseudo Random Bit Sequences (PRBS) defined by ITU-T 0.150 and 0.151 standards, fixed words and 24-bit or 32 bit

user defined patterns are available. Note, if the 32 bit user pattern entered is incorrect, the default pattern will be

0xFFFFFFFF.

Invert:

Inversion of PRBS polarity is also available. Inversion of fixed words is not permitted.

Go back to top

Go back to TOC

14.3.2 Measurements

Measurements tab

Manual mode is chosen as the default configuration for starting/stopping the test.

Go back to top

Go back to TOC

14.3.3 General

General tab

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды