VeEX VePAL TX300 Скачать руководство пользователя

Страница: 309 / 421

user simply has to enable/disable which tests to perform by checking/unchecking a selection box in the respective tab for each

test. By default all four tests are enabled.

The following parameters must be configured before running the RFC 2544 conformance test suite.

Throughput tab

Max Rate:

Up to 100% of the negotiated line rate. The default value is 100%.

This is the maximum transmit rate to perform the throughput test for each test frame size.

The user may configure this rate as a % of the total line rate or in Mbps. For example if the user configures the

Max Rate to be 90% and the negotiated line rate of the link is 100Mbps, then the maximum transmit rate will be

90Mbps or 90% of the line rate.

Resolution:

Input any value between 0.001% and 1%. The default value is 1%. Resolution refers to the resolution in

searching for the throughput rate. If 1% is selected, the throughput rate will be searched with ±1% accuracy.

Duration:

5 to 999 seconds. The default value is 20 seconds.

The duration is the amount of time the throughput test is run for, for each frame size at a given rate.

RFC 2544 Setup - Throughput Settings

Go back to top

Go back to TOC

Latency tab:

User configures the following:

Test:

Throughput Rate or Custom Rate. The default value is throughput.

Throughput rate

: Latency test will be performed at the throughput rate found for each of the tested frame sizes.

Custom rate:

User configures a custom rate in % or Mbps.

Rate:

Only available if Custom Rate is selected. Enter up to 100% of the negotiated line rate or enter the rate in Mbps.

Duration:

5 to 999 seconds. The default value is 20 seconds.

This is the amount of time that the latency test will be performed for each test frame size.

Repetitions:

1 to 100. The default value is 1.

This is the amount of times that the latency test will be repeated for each test frame size.

RFC 2544 Setup - Latency Settings

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды