VeEX VePAL TX300 Скачать руководство пользователя страница 327

Страница: 327 / 421

For EMIX (1GE only):

The default value is abceg. Tap the zoom (magnifying glass) icon to define other values.

Select the values from the drop down lists on the next screen.

Note:

Any EMIX configuration of 5 frames is allowed.

Encapsultaion Type:

None or

Provider Backbone Bridge (PBB-TE):

Provider Backbone Bridge MAC-in-MAC (IEEE

802.1ah) encapsulation are configured trunks that add resiliency and configurable performance levels in the provider

backbone network. Available for 1GE Copper/Fiber and 10GE port. PBB encapsulation is available for all Ethernet tests

(Layer 2,3 and 4) - BERT, RFC2544, Throughput, V-SAM.

Tap the PBB block to configure the settings. All PBB fields are configurable.

Backbone MAC Source

Backbone MAC Destination

Ethernet Type

I-SID

Backbone VLAN ID, Priority, Type

Please see

15.3.1 RFC 2544 Setup

and follow the setup procedure to configure the remaining Header Settings for V-SAM.

V-SAM Setup - Services - Header Settings

V-SAM Setup - Services - EMIX Frame Size Settings

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды