VeEX VePAL TX300 Скачать руководство пользователя

Страница: 13 / 421

1.0 About This User Manual

This user manual is suitable for novice, intermediate, and experienced users and is intended to help you successfully use the

features and capabilities of the VePAL TX300/e test set. It is assumed that you have basic computer experience and skills, and

are familiar with IP and telecommunication concepts, terminology, and safety.

Every effort was made to ensure that the information contained in this manual is accurate. However, information is subject to

change without notice. We accept no responsibility for any errors or omissions. In case of discrepancy, the web version takes

precedence over any printed literature.

in the USA and certain other countries. All trademarks or registered trademarks are the property of their respective companies.

No part of this document may be reproduced or transmitted electronically or otherwise without written permission from VeEX Inc.

This device uses software either developed by VeEX Inc. or licensed by VeEX Inc. from third parties. The software is confidential

and proprietary of VeEX Inc. The software is protected by copyright and contains trade secrets of VeEX Inc. or VeEX's licensors.

The purchaser of this device agrees that it has received a license solely to use the software as embedded in the device, and the

purchaser is prohibited from copying, reverse engineering, decompiling, or disassembling the software.

For more technical resources, visit the VeEX Inc. web site at

www.veexinc.com

. For assistance or questions related to the use of

this product, call or e-mail our customer care department for customer support. Before contacting our customer care department,

have the product serial number and software version ready. Please go to the

Basic Operations

section for details on locating the

unit serial number in the menus or locate the serial number on the back of the chassis. Please provide this number when

contacting VeEX customer service.

Customer Care:

Phone: + 1 510 651 0500

E-mail:

[email protected]

Website:

www.veexinc.com

Go back to TOC

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды