VeEX VePAL TX300 Скачать руководство пользователя страница 183

Страница: 183 / 421

10.2 SONET Tools

Accessing SDH/SONET Tools

On the TX300, tap on Home (main menu) >

Advanced Mode

SONET/SDH Tools

On the TX300e, tap on Home (main menu) >

SONET/SDH Tools

10.2.1 Shortcuts

SDH/SONET Tools Menu

Overhead Analyzer:

Displays the Section/Line Overhead (SOH) and STS Path Overhead (POH) bytes of the received

channel.

Overhead Generator:

Used to edit Section/Line Overhead (SOH) and STS Path Overhead (POH) bytes of the received

channel.

Pointer Tasks:

Displays both STS and VT pointer values and generates STS and VT pointer movements. Pointer

sequences according to Bellcore GR.253 recommendations are also possible.

Trace Identifier:

Used to generate and edit J0, J1 and J2 path traces and set expected trace for received channel

according to G.831 recommendations.

Payload Labels:

Used to set the C2 and V5 Path Signal Labels which indicate the content of the STS path and VTs.

APS Testing:

Used to measure Automatic Protection Switching limits. Using selectable triggers, the drop out times of

tributary connections are measured and compared with preset values.

TCM Tasks:

Used to analyze or edit the sequence of Z5 and Z6 TCM bytes by generating alarms and errors in the

Tandem connection sub-layer.

Tributary Scan:

Used to scan individual or multiple tributaries to verify routing and error free operation. Available in VT-

1.5 or VT-2 mode

Round Trip Delay (Propagation Delay):

Measurement works by sending a test pattern. Bit errors are transmitted in the

pattern. The time it takes for the error to reach the receiver is the propagation time through the network.

Go back to top

Go back to TOC

10.2.2 Overhead Analyzer

Tap the Overhead Analyzer icon to display the OH screens shown below. There are tabs for:

SOH RX, which displays the bytes associated with the Section/LINE Overhead

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды