VeEX VePAL TX300 Скачать руководство пользователя страница 282

Страница: 282 / 421

15.2 BERT

Setup

Overview
Header Settings

PBB
MAC
VLAN
Data
MPLS
IP
Data
RX Filter

Traffic Settings

Error Injection
Starting / Stopping a BERT
Results

Summary
Errors
Events
Traffic
Rates
Delay
Alarms
Signal

15.2.1 BERT Setup

Overview:

BER testing at Layer 1, 2, 3, and 4 is supported. The BERT can be configured to use either regular PRBS test patterns, stress

patterns (specifically for 10Gigabit Ethernet) or user defined test patterns to simulate various conditions. The test layer, frame

header, traffic profile, error injection, and control settings of the far-end device (if applicable) must be configured prior to testing.

Layer 1:

Unframed mode (fiber ports only) or Framed mode

Unframed mode:

Test traffic consists of a bit stream of the selected test pattern

Framed mode:

Test pattern is encapsulated into a valid Ethernet frame with SOF, Preamble, and CRC field

BERT Setup - Header (Layer 1)

Layer 2:

Framed BERT (same as Layer 1 Framed)

MAC Address:

A default or user configured Media Access Control (MAC) address is added to the frame

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды