Spectra Logic T-Series Spectra T24 Скачать руководство пользователя страница 78

Страница: 78 / 103

Appendix B. Library Specifications

Physical Specifications

Environmental Specifications

Measure

Library Alone

Packaged Library

Height

3.5 in (87.6 mm)

9.8 in (248 mm)

Width

17.6 in (447.5 mm)

23.5 in (598 mm)

Depth

29.1 in (740 mm)

a. As measured from rack mount ears.

39.1 in (993 mm)

Approx. Weight

40 lbs (18 kg)

b. Library weight with one drive installed.

41 lbs (18.5 kg)

c. Weight with one half-height drive installed, accessories in package, etc.

43 lbs (20 kg)

d. Library weight with two drives installed.

44 lbs (20 kg)

e. Weight with one half-height drive installed, accessories in package, etc.

Characteristic

Specification

Operating Temperature

50º to 95º F (10º to 35º C)

Non-Operating Temperature

-22º to 140º F (-30º to 60º C)

Maximum Rate of Temperature Change

18º F (10º C) per hour

Dust Concentration

Less than 200 microgram/cubic meter

Altitude (Operating)

13,000 ft (4200 m) at 25˚C ambient

Operating Humidity

20% to 80% non-condensing

Non-Operating Humidity

20% to 80% non-condensing

Содержание T-Series Spectra T24








































































































Результаты поиска

Содержание T-Series Spectra T24

Отзывы:

Похожие инструкции для T-Series Spectra T24

Бренды по названию

Популярные бренды

Spectra Logic T-Series Spectra T24, Руководство пользователя

Результаты поиска

Содержание T-Series Spectra T24

Отзывы:

Похожие инструкции для T-Series Spectra T24

Бренды по названию

Популярные бренды