Smiths Medical Medfusion 3500 Скачать руководство пользователя страница 10

Страница: 10 / 152

Medfusion® Model 3500 pump V6

Operator’s Manual

Introduction

CAUTION: ALWAYS

verify that the software

version of the pump (displayed on screen during

power-up) and

Operator’s Manual

are the same. Refer

to this manual’s front page.
The Medfusion

Model 3500 pump V6 is a small,

lightweight and portable syringe infusion pump.

The pump offers a variety of delivery modes

programmable to meet specific patient care needs.

The actual modes available on a given pump, and

their location on a given screen, depend on the

custom setup. Fluids can be delivered from a variety

of syringe sizes (1-60 mL) and syringe manufacturers

in various delivery modes.
The Medfusion

Model 3500 pump V6 is equipped

with PharmGuard

Medication Safety Software, an

intuitive system designed to enhance safety while

maintaining simplicity, which can allow streamlined

implementation and improved work flow.
A pump

Configuration

is created on a PC

using the PharmGuard

Toolbox 2, Version 3

software (PharmGuard

Toolbox 2), and then the

Configuration is sent to the pump. The Configuration

may contain global settings, Profile definitions, library

definitions, Drug Programs and syringe definitions

(see page 14 for discussion about libraries).
The Medfusion

Model 3500 pump V6 imports and

exports data to assist in history data management.

The pump communicates via the IR port on the rear

of the pump. Pump Configurations and firmware can

be updated, and infusion settings and events history

downloaded in combination with the PharmGuard

Toolbox 2 software application.
The pump also has the FlowSentry™ pressure

monitor (rapid occlusion detection) feature, which

is a comprehensive array of pressure-related safety

features, including rapid alarm response and

reduced false alarms. Pressure trending is shown

in the pump display, allowing earlier opportunities

for intervention, as well as a post-occlusion bolus

reduction feature.

Indications for use

The Medfusion

Model 3500 pump V6 is indicated

for the following uses:

• In the administration of fluids requiring precisely

controlled infusion rates including blood or

blood products, lipids, drugs, antibiotics, enteral

solutions and other therapeutic fluids.

• By the following delivery routes: arterial, epidural,

intravenous, intrathecal, subcutaneous and

enteral.

• By the following delivery modes: continuous,

volume/time, mass, body surface area, body

weight, intermittent and bolus.

• In critical care, anesthesia, neonatal and pediatric

applications or other healthcare settings where

the use of the syringe infusion pump can be

monitored or supervised by a clinician.

• Inside the MRI room mounted outside the 150

Gauss line and with shielded magnets of field

strength of 1.5 Tesla.

WARNINGS:

• This equipment/system is intended for use by

healthcare professionals only.

• Before using any Medfusion

Model 3500 pump

V6, users must be thoroughly familiar with the

contents of the operator’s manual, including all

warnings, cautions, and instructions for use.

• The user should ensure that the performance

offered by the pump is fit for the intended use and

that the pump is not used in any way or for any

purpose other than its intended purpose.

• This pump is not to be used in any intra-articular

space infusion.

• If the pump is used to deliver life-sustaining

medications, an additional pump must be

available for situations where an interruption in

infusion could be dangerous.

• The pump must be positioned in an MR

environment such that it is

secured to a non-

moveable object

and the magnetic fringe field

does

not exceed 150 gauss

. Exposing the Medfusion

Model 3500 pump to magnetic fields that exceed

150 gauss presents a risk of becoming a projectile

hazard and can lead to possible patient injury or

death. Irreversible damage to the pump can also

occur, rendering it inoperable.

Содержание Medfusion 3500

























































































































































Результаты поиска

Содержание Medfusion 3500

Отзывы:

Похожие инструкции для Medfusion 3500

Бренды по названию

Популярные бренды

Smiths Medical Medfusion 3500, Руководство оператора

Результаты поиска

Содержание Medfusion 3500

Отзывы:

Похожие инструкции для Medfusion 3500

Бренды по названию

Популярные бренды