manualshive.com logo in svg

Siemens AXIOM Iconos R200, Руководство оператора, Страница: 26 / 238

Поделиться
Скачать
Siemens AXIOM Iconos R200 Скачать руководство пользователя страница 26

System Overview

Protective Measures

18 

/ 44

AXD3-340.620.13.01.02

Operator Manual

These objects are not detected by the collision monitoring of the unit. Avoiding 
collisions of the unit with these objects is subject to the operator’s duty to take 
care.

If a collision of the unit with a rigid obstacle (e.g. step) has occurred,

◆

press one of the red emergency stop buttons,

◆

rescue the patient,

◆

immediately notify the SIEMENS Uptime Service.

❏

Avoid standing or sitting immediately adjacent to the system and especially 
do not sit next to the system with your legs or knees under the cross-beam at 
the head or foot end of the table.

❏

Take care that during system movements no one is in the area between the 
unit base and table.

❏

Take care that with the footboard attached there is a risk of collision with the 
extended cone (optional) when the tabletop and / or the longitudinal carriage 
are moving.

❏

Do not grasp in the loading shaft of the spotfilm device because of the risk of 
crushing.

Patient positioning

❏

All safety-related equipment must be installed and operable. In particular the 
handgrip strips (head end and lateral), handgrip, footboard, foot restraints, 
compression belt and shoulder supports.

❏

The patient’s hands, arms, legs, head and hair must not extend unsecured be-
yond the edge of the tabletop.

❏

Observe the patient while moving the tabletop and in system movements and 
take care that any catheter is correctly located.

❏

In examinations with the table tilted up vertically, the footboard serves as an 
adjustable step or seat.
– Ensure that the footboard is locked together with the tabletop on both 

sides.

– Check the firm location of the footboard.

Warning

Under no circumstances must the unit be tilted down further or tilted up, since 
externally invisible, but safety-relevant damage to the tilting drive may occur. 
Severe consequential damage including personal damage cannot be excluded 
in this case.

Содержание AXIOM Iconos R200















































































































































































































































Отзывы:

Нет отзывов