SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 65

Страница: 65 / 81

12.5. USING THE PINPOINT-GIS APP

The application is freely available in the Android Play store and can be used with the

Altus NR2, Altus GeoPod or the APS-3 receiver.

The following steps will guide you through using PinPoint-GIS App with the Altus NR2

receiver using Collector for ArcGIS as an example.

1-Install the PinPoint-GIS App

•

The app can be installed in your mobile Android

device from the Google play store.

PinPoint-GIS App will work only when you enable

Mockup Locations on your mobile device. To do

this go to, Settings

→

Developer options,

in your mobile device and make sure that the

‘Allow mock locations’ option is enabled. Opening

the app will also guide you through these settings

when Mockup Locations is disabled.

2-Connect to the Internet using the
internal Cellular/GSM on the Altus NR2

•

Section 12.3 describes how this can be done

3-Open the app and connect

•

Click on the PinPoint-GIS App icon

•

The

PinPoint-GIS

App

will

try

make

automatic connection to the Altus NR2.

If you

have the WiFi connection enabled then it will

automatically connect to the receiver. If you want

to connect via Bluetooth then you can create

a new connection by going to the Connection

manager in the app.

The

ﬁrst

time

you

perform

Bluetooth

connection it will require a pairing to the Altus

NR2 (which can also be done from the connection

manager)

4-Override the GPS location

•

Your mobile device has also an internal GPS

receiver therefore you need to override the GPS

location by using the external Altus NR2 accurate

position.

•

In the App Settings menu of the app you can ﬁnd

the Location Overriding option.

•

Note that when you override the internal GPS

position,

other applications running on your

device will now also use the Altus NR2 position.

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды