SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 59

Страница: 59 / 81

12.4. USING PINPOINT-GIS WEB

12.4 Using PinPoint-GIS Web

PinPoint-GIS Web allows you to perform data collection which is synchronized directly with

Esri ArcGIS Online.

It works on any platform with a web browser and makes the bridge

between GIS and accurate data collection.

The following steps will guide you through the main functionalities of PinPoint-GIS Web in

combination with the Altus NR2 receiver.

The PinPoint-GIS view is located in the GNSS/PinPoint-GIS menu of the web interface

as shown in Figure 12-2.

Within this view you have full access to your ArcGIS Online

user maps.

The system allows you to select your ArcGIS Online user maps, change the

background of your user map using the multiple Basemaps available from Esri, Display or

hide the different layers and ﬁlters of your map, and will allow you to have conﬁgurability

for Portal for ArcGIS in the case your data is located in an speciﬁc secured ArcGIS Server.

Figure 12-2:

PinPoint-GIS Web menu

Navigation within the PinPoint-GIS Web view is straightforward and allows you to visualize

all the main GIS and GNSS information in a single view. The view can easily be maximized

using the maximize/minimize button in the right corner of the map

. This is handy when

working in the ﬁeld with tablet screens.

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды