SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 70

Страница: 70 / 81

14.1. CONFIGURATION

the Altus NR2 allows storing two user proﬁles or user conﬁgurations, User 1 and User2.

The user can store a conﬁguration into a user proﬁle by simply copying the Boot or the

Current conﬁguration to User1 or User2.

To restore a user proﬁle, the User1 or User 2 conﬁguration is copied into Boot or Current.

The table below gives an overview of the Altus NR2s conﬁgurations.

Conﬁguration

Persistent?

Writable?

Description

RxDefault

Yes

Contains the factory default.

Current

Yes

Settings that are actually being

used.

Boot

Yes

The values of Boot are copied into

Current at start up.

User1, User 2

Yes

Two conﬁgurations can be stored

for later use.

Table 14.1-1:

Altus NR2 Conﬁgurations

The Web Interface provides the following operations on conﬁgurations:

Copy

The Copy operation allows the user to copy any of the ﬁve

conﬁgurations into another conﬁguration.

Download

The Download operation allows the user to export a selected

conﬁguration to a text ﬁle.

Upload

The Upload operation allows the user to import a selected

conﬁguration from a text ﬁle.

Table 14.1-2:

Altus NR2 Conﬁgurations

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды