SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 41

Страница: 41 / 81

10 Conﬁguration of the Altus NR2 as a

Base

Before you start ...

The Altus NR2 offers the possibility of being setup as a Base station receiver. This makes

a great companion to any Altus NR2 Rover unit thanks to its point-to-point connectivity

features.

The RTK Differential corrections can be output over any of the following communication

channels:

• Cellular

• WiFi

• COM1 port (e.g. to and external UHF radio)

• Bluetooth

One main advantage of the Altus NR2 is the possibility of connecting two NR2s point-to-point

directly without an intermediate device as corrections are sent directly between rover and

Base.

Please note that position output by the rover in an RTK setup is relative to the Base station.

For this reason, unless only relative positioning is needed, it is always recommended to use

a properly surveyed position for the Base station receiver.

Using a cellular connection, it is possible provide corrections to up to 8 Rovers (provided

that 3G cellular connection is available)

Using Wi-Fi, it is possible to connect to up to 4 Rover units (one unit should be setup

as an Access Point and the others as Wi-Fi Clients).

Base

→

Rover conﬁguration via Cellular requires you to know the IP address of the

Cellular modem.

The Altus NR2 has DGNSS Base enabled by default with only the Altus NR2 C and

Altus NR2 Base variants having RTK Base functionality.

The following sections detail how to conﬁgure a base-rover setup using two Altus NR2

units. Only Cellular and Wi-Fi connections between base and rover are described however,

differential correction data can also be transferred over Bluetooth or a serial COM

connection.

Some

mobile

network

providers

not

allow

communication

point-to-point

using

GSM/Cellular

connections. If the setup is not possible please contact your mobile network provider.

Some network providers allow you to use Fixed IP addresses.

This can be useful when you want the

receiver to boot with the same conﬁguration every time as the IP address will not change after a new connection

is made. Please contact your mobile network provider for further information.

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды