SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 20

Страница: 20 / 81

4 Initial set up

4.1 Prerequisites

An Activated Micro SIM Card

•

In some countries a PIN and PUK code are required to use the SIM card. If so, make

sure you have the codes at hand.

•

To establish a data connection, an Access Point Name (APN), user name and password

are needed.

If you do not have this information, you need to request it from the

telecom provider.

An active RTK (NTRIP or TCP/IP) service

•

A subscription for a (NTRIP or TCP/IP) correction service or an Altus NR2 Base receiver

for getting corrections (not applicable for Altus NR2 M or Altus Base models)

Charged Batteries

•

Make sure you have two charged batteries.

•

Empty batteries may take three to four hours to charge.

An Altus NR2 Wall Charger

•

As an alternative you can power the Altus NR2 using the wall charger when conﬁguring

the Altus NR2.

A Wi-Fi or USB connection to a phone, tablet or computer

•

A Wi-Fi enabled device can be used to conﬁgure the Altus NR2 using the Web Interface.

•

Any device with a USB port can also be used to connect via the Web Interface and

conﬁgure the Altus NR2.

An ArcGIS Online subscription for the PinPoint-GIS

•

Using Septentrio’s PinPoint-GIS Web you will be able to perform GIS data collection

which synchronizes directly with ArcGIS Online.

•

For subscriptions to ArcGIS Online please visit

https://www.arcgis.com

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды