SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 53

Страница: 53 / 81

11.2. ALTUS NR2 RTK BASE-ROVER WI-FI CONNECTION

Conﬁgure the IPR connection

Setup an IPR (Receive) connection for reception of differential corrections.

On the

‘Communication/IP Settings’ menu, conﬁgure and IPR connection with the same port number

conﬁgured for the Base station and the IP address

192.168.20.1

as shown in Figure 11-16.

Figure 11-16:

Conﬁgure the rover receiver to listen for the diff corr ouptut from

the Base station

Step 4: Verifying the conﬁguration

If both the Base station and rover receivers have been conﬁgured correctly, the rover

‘Overview’ tab should show the Wi-Fi connection to the base station and the top panel

positioning mode icon should indicate RTK ﬁxed as shown in Figure 11-17/

Figure 11-17:

If the conﬁguration is correct, the Wi-ﬁ panel should show a

connection to the Base station and the top-panel icon indicate RTK ﬁxed

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды