SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 12

Страница: 12 / 81

1.9. IC REGULATIONS

1.9 IC Regulations

RSS-Gen 7.1.3

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is

subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference,

including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si

le brouillage est susceptible d’en compromettre le fonctionnement.

1.9.1 IC RF Exposure Compliance (MPE)

This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled

environment.

This equipment should be installed and operated with minimum distance

20 cm between the radiator and your body.

1.9.2 Déclaration d’exposition aux radiations

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum

de 20 cm de distance entre la source de rayonnement et votre corps.

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды