SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 81

background image

9.2. USING THE USB CONNECTION

9.2.3 Connecting via ‘Ethernet over USB’

The web Interface of the Altus NR2 can be accessed over an ‘Ethernet over USB’ connection.

If the Altus NR2 has not been connected to the computer being used before then ﬁrst

execute the steps described in the Section 9.2.1.

If the Altus NR2 has already been connected to the computer used the following steps

apply:

• Connect the Altus NR2 to your computer using the USB cable.

• Open your web browser and use the IP address:

192.168.3.1

40

«
...
38
39
40
41
42
...
»

Содержание Altus NR2


















































































Отзывы:

Нет отзывов

Похожие инструкции для Altus NR2

Бренд: Cambium Networks Страницы: 68

Бренд: Cambium Networks Страницы: 110

Бренд: Fortinet Страницы: 20

OMB-DAQBOARD-3000 Series

Бренд: Omega Страницы: 108

Бренд: Altera Страницы: 93

NetVanta 6355 PoE

Бренд: ADTRAN Страницы: 46

Бренд: Sangamo Страницы: 2

Dimension ES-3124

Бренд: ZyXEL Communications Страницы: 228

Бренд: Moxa Technologies Страницы: 36

LMP-1202M-SFP Series

Бренд: ANTAIRA Страницы: 2

Бренд: BinTec Страницы: 34

Бренд: Loopcomm Страницы: 2

Бренд: AC Infinity Страницы: 24

Бренд: Intel Страницы: 578

Бренд: JAKA Страницы: 37

H8S/2646 Series

Бренд: Renesas Страницы: 20

Бренд: Socket Страницы: 28

Secure Site Manager 16

Бренд: Black Box Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды