SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 7

Страница: 7 / 81

1.2. ALTUS NR2 TECHNICAL CHARACTERISTICS

1.2 Altus NR2 Technical Characteristics

132 Channel GPS + G SBAS receiver

Integrated 3.5G Quad-Band GSM/GPRS/EDGE + HSPA Modem

Integrated Wi-Fi 802.11 b/g/n

Integrated Bluetooth 2.1 + EDR/4.0

Web Interface conﬁguration

Hot-Swap Li-Ion Batteries

Onboard 8 GB Memory

Onboard GIS collection thanks to PinPoint-GIS

With Septentrio’s open architecture philosophy, you have the choice of using data collector

software from MicroSurvey FIELDGenius or Carlson SurvCE.

1.2.1 GNSS Key Features

132 Channels with L1/L2/L2C GPS, GLONASS and SBAS.

RTK, SBAS, DGPS and Standalone positioning modes.

Navigation performance

Horizontal

Vertical

Standalone

1.3 m

1.9 m

SBAS (WAAS, EGNOS, MSAS)

0.6 m

0.8 m

DGPS (RTCM1,3 / 9,3)

0.5 m

0.9 m

RTK (Fixed)

0.6 cm + 0.5 ppm

1 cm + 1 ppm

The Altus NR2 can be mounted on a standard survey rod with a 5/8” thread.

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды