SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 21

Страница: 21 / 81

4.2. INSERT THE MICRO SIM CARD

4.2 Insert the micro SIM card

Turn off the Altus NR2 to install or remove the SIM card. Damage to the SIM
card may occur if installed or removed while the unit is powered.

1. Put the Altus NR2 on a ﬂat surface with its battery compartments facing up as shown

in Figure 3 on page 15.

2. Open the battery compartment.

3. Open the SIM card compartment

4. Put the micro SIM card down in the SIM card compartment.

5. Slide the micro SIM card gently towards the front panel of the Altus NR2 until a click

sounds.

6. Gently close the SIM card compartment.

4.3 Insert the batteries

1. Place the two batteries in their compartments with their positive leads pointing to the

front panel of the Altus NR2.

2. Close the two battery doors. The doors click audibly when latched.

4.4 Switch on the Altus NR2

Click the power button once to switch on the Altus NR2.

4.5 Wait for the Altus NR2 to start up

•

It takes about

30 seconds

for the Altus NR2 to fully boot up.

•

It is advised to avoid pressing the power button during the start up sequence.

•

During the start up sequence, the LEDs will blink before they stabilize and indicate the

correct status.

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды