SEPTENTRIO Altus NR2 Скачать руководство пользователя страница 2

Страница: 2 / 81

User Manual

Revision 1.1.0

Applicable to version 1.1.0 of the Altus NR2 Firmware

September 24, 2015

Septentrio and the Septentrio logo are trademarks of Septentrio NV registered in Belgium,

the U.S. and other countries. No part of this document may be copied, used or reproduced

without the prior written permission of Septentrio NV.

No part of this manual me by reproduced or transmitted in any form or by any means,

electronic or mechanical, including photocopying and recording, or any purpose without the

express written permission of Septentrio NV.

Mention of third-party products in this document is for informational purposes only

and does not constitute an endorsement or a recommendation. Septentrio NV assumes

no responsibility with regard to the performance or use of the Altus NR2 due to GNSS

characteristics,

USA Department of Defense operations control,

atmospheric effects,

multipath and RF interference. All understandings, agreements, or warranties take place

directly between the seller and the prospective users. Every effort has been made to ensure

that the information in this manual is accurate. Septentrio NV is not responsible for printing

or clerical errors. All speciﬁcations are typical and subject to change without prior notice.

Septentrio

Greenhill Campus, Interleuvenlaan 15G

B-3001 Leuven, Belgium

http://www.septentrio.com

[email protected]

Phone:

+32 16 300 800

Fax:

+32 16 221 640

@Septentrio

Содержание Altus NR2


















































































Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды

SEPTENTRIO Altus NR2, Руководство пользователя

Результаты поиска

Содержание Altus NR2

Отзывы:

Похожие инструкции для Altus NR2

Бренды по названию

Популярные бренды