Schweitzer Engineering SEL-2032 Скачать руководство пользователя страница 9

Страница: 9 / 354

Date Code 20120126

Instruction Manual

SEL-2032

Communications Processor

List of Figures

Typical Integrated Substation System .................................................................................... 1.3

Figure 1.2

Traditional SCADA System ................................................................................................... 1.4

Figure 1.3

IEDs Communicating With RTU ........................................................................................... 1.4

Figure 1.4

Integrated Substation Without a Communications Processor ................................................ 1.6

Figure 1.5

System Integrated Using the SEL-2032 Communications Processor .................................... 1.6

Figure 1.6

Multitiered SEL-2032 System................................................................................................ 1.9

Figure 1.7

SEL-2032 Manages Communications With Multiple Master and Slave Devices................ 1.14

Figure 1.8

SEL-2032 Database Structure .............................................................................................. 1.17

Figure 1.9

User Region/SET M Setting Operation................................................................................ 1.19

Figure 1.10

Transparent Connection Provides Direct Access to Many IEDs Through a

Single Connection Point (Modem) ................................................................................... 1.23

Figure 1.11

SEL-2032 Distributes Time Synchronization Using IRIG-B Over Star

Data and Control Network Connections........................................................................... 1.24

Figure 2.1

9-Pin Connector Pin Number Convention.............................................................................. 2.5

Figure 2.2

Cable C234A Pinout Configuration ....................................................................................... 2.8

Figure 2.3

SEL-2032 Front and Rear Panels ......................................................................................... 2.11

Figure 2.4

SEL-2032 Main Board Jumper Location ............................................................................. 2.12

Figure 2.5

SEL-2032 Optional I/O Board Jumper Location ................................................................. 2.13

Figure 2.6

SEL-2032 Dimensions and Panel-Mount Cutout................................................................. 2.14

Figure 2.7

ACCESS Command Screen ................................................................................................. 2.15

Figure 2.8

STATUS Command Screen .................................................................................................. 2.16

Figure 2.9

AUTO 2 Command Displays Fast Message Features .......................................................... 2.18

Figure 2.10

Issue the WHO Command to Verify Relay Port Connection ............................................... 2.19

Figure 2.11

MAP 2 Command Verifies Data Types and Locations......................................................... 2.20

Figure 2.12

MAP 2:METER Command Verifies Metering Quantities ................................................... 2.21

Figure 2.13

MAP 2:TARGET Command Displays TARGET Region Data............................................ 2.22

Figure 2.14

STATUS Command Checks Communication and Data Retrieval........................................ 2.23

Figure 3.1

Commands Available ............................................................................................................. 3.2

Figure 3.2

Changing Access Levels ........................................................................................................ 3.3

Figure 3.3

Using the PAS Command....................................................................................................... 3.3

Figure 3.4

SEL-2032 Configured With SEL-251 Relays, External Modem, and IRIG-B Source .......... 3.4

Figure 3.5

Global Data Region Contents................................................................................................. 3.7

Figure 3.6

Settings COPY Command Example ...................................................................................... 3.9

Figure 3.7

STATUS Command Example............................................................................................... 3.10

Figure 3.8

Initiate Transparent Communications .................................................................................. 3.11

Figure 3.9

Relay Group 1 Settings ........................................................................................................ 3.12

Figure 3.10

Terminate Transparent Communications ............................................................................. 3.12

Figure 3.11

TOGGLE Command Example ............................................................................................. 3.12

Figure 3.12

Example AUTO Command Output ...................................................................................... 3.14

Figure 3.13

WHO Command Example ................................................................................................... 3.15

Figure 3.14

MAP Command Example .................................................................................................... 3.16

Figure 3.15

MAP 2:METER Command Example................................................................................... 3.17

Figure 3.16

Example MAP Command on the TARGET Region............................................................. 3.18

Figure 3.17

STATUS Command Example............................................................................................... 3.18

Figure 3.18

Example AUTO Command Output ...................................................................................... 3.21

Figure 3.19

Example SET A 3 Settings................................................................................................... 3.21

Figure 3.20

View 3:USER Output ........................................................................................................... 3.22

Figure 3.21

Math/Move Equations and 17:USER Contents.................................................................... 3.22

Figure 3.22

Non-SEL IED Attached to Port 12....................................................................................... 3.24

Figure 3.23

TOGGLE Command Asserts the D1 Bit on Port 12 ............................................................ 3.26

Figure 3.24

Received Message ................................................................................................................ 3.28

Figure 3.25

Response Message................................................................................................................ 3.28

Figure 3.26

Port 3 Meter Region Data Map ............................................................................................ 3.30

Figure 3.27

Port 4 Meter Region Data Map ............................................................................................ 3.30

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации

Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды