manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.29

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Settings

User-Defined (SET U) Commands

WRITE,

 and 

TRANS

 special purpose commands may be useful with master 

devices that you can program to communicate automatically with the 
SEL-2032.

To build these commands, you must specify the position and format of the port 
number, address, and data, as applicable, within the message. You then specify 
how the SEL-2032 should respond to each of these commands for both 
successful and unsuccessful operations.

For example, assume you have made the following settings. See 

Section 5: 

Message Strings

 for an explanation of the special characters used in these 

settings. 

TRANS = "TR\Pa/" TRANSACK = "\006" TRANSNACK = "\015"

To enter transparent 

mode with another SEL-2032 port, use the message format you 
defined with the 

TRANS

 command. For example, to enter transparent 

mode with Port 5 with these settings, issue the command 

TR05 

<Enter>

. If the transparent connection is successful, the SEL-2032 

responds with 06h (ASCII ACK) and you will be transparently 
connected. To terminate the transparent connection, use the transparent 
disconnect sequence you set using SET P. If the transparent connection 
could not be established, the SEL-2032 responds with 15h (ASCII 
NACK). 

READ = "RD\Pa/@\Aa/" READACK = "RP\Dh/" READNACK = ""

To read data from the 

SEL-2032 database, use the message format you defined with the 

READ

 command. To read from Port 7's database at address 1001h 

with these settings, send the command 

RD07@1001 <Enter>

. The 

SEL-2032 will respond with the data if the read is successful (e.g., 
RP0013). If the read cannot be performed, the SEL-2032 will not 
respond, because there is no response defined for a failed read 
(READNACK) in these settings. 

WRITE = "WR\Pa/@\Aa/=\Dh/" WRITEACK = "OK" WRITENACK = "FAIL"

To write data to 

the SEL-2032 database, use the message format you have defined with 
the 

WRITE

 command. To write 0036h to Port 11's database at 

address D007h with these settings, send the message 

WR0B@D007=0036 <Enter>

 to the SEL-2032. The SEL-2032 

responds “OK” if successful, or “FAIL” if the write could not be 
performed. 

This example uses ASCII commands, but these commands could also have 
been built as binary commands.

SET U Settings

The 

SET U

 command prompts you for user-defined strings and the command 

you want to use to trigger a response on Master, SEL IED, and other IED 
ports. 

SET U

 is not applicable to printer ports. You can also use the 

SET U

 

command to disable the SEL-2032 command set on Master ports. 

Table 7.7

 

includes detailed information about the 

SET U

 settings.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Patton electronics 2888 Getting Started Manual preview
2888
Бренд: Patton electronics Страницы: 51
Baldor Modbus Plus Installation And Operating Manual preview
Modbus Plus
Бренд: Baldor Страницы: 34
ICT Protege PRT-PX16-PCB Installation Manual preview
Protege PRT-PX16-PCB
Бренд: ICT Страницы: 34
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Бренд: XJTAG Страницы: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Бренд: Xilinx Страницы: 8
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Бренд: LevelOne Страницы: 3
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Бренд: FiberHome Страницы: 2
Lanner NCA-6520 User Manual preview
NCA-6520
Бренд: Lanner Страницы: 141
Omron CJ1W-CRM21 Operation Manual preview
CJ1W-CRM21
Бренд: Omron Страницы: 172
JETWAY JNLH61S-6C Series User Manual preview
JNLH61S-6C Series
Бренд: JETWAY Страницы: 36
Patton electronics 593/25, 593/45, 593/TB, RS-422, RS-485 User Manual preview
593/25, 593/45, 593/TB, RS-422, RS-485
Бренд: Patton electronics Страницы: 8
ICP DAS USA PEX-P8R8i Quick Start Manual preview
PEX-P8R8i
Бренд: ICP DAS USA Страницы: 9
Korg EXBP-MP3 User Manual preview
EXBP-MP3
Бренд: Korg Страницы: 8
MSI MPG SEKIRA 500X Manual preview
MPG SEKIRA 500X
Бренд: MSI Страницы: 2
MSI MPG CORELIQUID K240 User Manual preview
MPG CORELIQUID K240
Бренд: MSI Страницы: 20
Aaeon PFM-620S Manual preview
PFM-620S
Бренд: Aaeon Страницы: 45
abaco systems PEX430 Hardware Reference Manual preview
PEX430
Бренд: abaco systems Страницы: 51
Crestron 4 Channel Fan Speed Control Module CLX-1FAN4 Specifications preview
4 Channel Fan Speed Control Module CLX-1FAN4
Бренд: Crestron Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды