manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.25

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Settings

Automatic Message (SET A) Settings

Automated
Control

You can associate SEL

OGIC

 control equation elements with specific SEL IED 

operations by enabling the SEND_OPER setting. Changes in these elements 
can then cause the SEL-2032 to directly issue operate commands to the 
attached SEL IED.

To find out what is associated, use the 

AUTO 

n

 command to determine the 

number of supported breakers and remote bits for operate control. For every 
breaker supported, one BR

n

 bit is associated with an SEL IED breaker. For 

every remote bit supported, one RB

n

 bit is associated with an SEL IED remote 

bit. Setting and clearing of BR

n

 bits corresponds to issuing 

OPEN

 and 

CLOSE

 commands, respectively. When SEND_OPER=Y, setting and 

clearing of RB

n

 bits correspond to issuing remote bit set and clear commands, 

respectively. When SEND_OPER=YP, setting RB

n

 bits corresponds to issuing 

remote bit pulse commands and clearing RB

n

 bits has no direct effect.

If the attached SEL IED is an SEL-2032, the 16 breakers correspond to the 
BR1 bits on each port. Similarly, the 16 remote bits correspond to the RB1 bits 
on each port. For example, if you set BR5 in the local SEL-2032 on a port 
auto-configured with an SEL-2032 attached, the command to set Port 5 BR1 is 
issued to the attached SEL-2032.

The SEL-2032 can issue these commands in one of two ways: ASCII or 
binary. The 

AUTO

 command tells you which is supported. When ASCII 

commands are used, the SEL-2032 has to wait for any ASCII communications 
in process to complete before issuing the command. If binary commands are 
used, the SEL-2032 issues the command to the attached SEL IED within 100 
milliseconds.

The operate commands are issued on the rising edge of the set and clear bits, 
unless they both rise simultaneously. Consequently, the breaker and remote 
bits track the value of the last operation performed by the SEL-2032. The 
relay may operate breakers or have its remote bits changed independent of the 
SEL-2032, so you cannot depend on the state of the breaker and remote bits to 
indicate the state of the relay.

If you wish to block the operation of one of these bits, assign both the set and 
clear equations to a blocking element. For instance, if you use X to block 
breaker one operations, you would set the equations to:

SBR1 = X CBR1 = X

With both the set and clear elements asserted, there can be no rising edges to 
trigger operate commands.

ARCH_EN

a

Enable use of archive data items 
(Y/N). 

You enter Y (Yes) to enable use of nonvolatile memory. ARCH_EN is 
forced to N (No) if nonvolatile Flash memory is not installed. Not
available for printer ports.

USER

Size of user-defined data space in 
registers. 

You enter the number of registers you need to use for data storage in the 
User region of memory. This may be automatically increased during
SET M operations.

a

Set ARCH_EN=Y, to enable the archive AUTO settings.

Table 7.6

Automatic Message (SET A) Settings Information 

 (Sheet 3 of 3)

Setting

Comment

Description

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Data Translation DT330 Series Getting Started Manual preview
DT330 Series
Бренд: Data Translation Страницы: 60
Garland P1GCCAS Installation Manual preview
P1GCCAS
Бренд: Garland Страницы: 4
Telex Communications 2472AA Instruction Manual preview
2472AA
Бренд: Telex Communications Страницы: 28
TANDBERG D5018501 Hardware User Manual preview
D5018501
Бренд: TANDBERG Страницы: 3
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Бренд: red lion Страницы: 5
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Бренд: Ubiquiti Страницы: 23
ICOP Technology Vortex86SX VSX-6100 User Manual preview
Vortex86SX VSX-6100
Бренд: ICOP Technology Страницы: 50
Powerleap PL-PROMMX Manual preview
PL-PROMMX
Бренд: Powerleap Страницы: 28
TDK HHM Series HHM1521 Specifications preview
HHM Series HHM1521
Бренд: TDK Страницы: 2
Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011 Datasheet preview
2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011
Бренд: Intel Страницы: 172
Dataprobe iBoot-PDU4-C10 User Manual preview
iBoot-PDU4-C10
Бренд: Dataprobe Страницы: 72
Adeunis RF COMFORT LwM2M User Manual preview
COMFORT LwM2M
Бренд: Adeunis RF Страницы: 68
IEI Technology PCIE-Q470 User Manual preview
PCIE-Q470
Бренд: IEI Technology Страницы: 90
Cambium Networks PTP 820C User Manual preview
PTP 820C
Бренд: Cambium Networks Страницы: 672
Spectravideo SVI-707 User Manual preview
SVI-707
Бренд: Spectravideo Страницы: 40
AVYCON HN500 Series Quick Start Manual preview
HN500 Series
Бренд: AVYCON Страницы: 2
ADLINK Technology DLAP-211-JNX Series User Manual preview
DLAP-211-JNX Series
Бренд: ADLINK Technology Страницы: 47
GarrettCom Mini-Concentrator Magnum 700X Installation And User Manual preview
Mini-Concentrator Magnum 700X
Бренд: GarrettCom Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды