manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

2.19

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Installation

Getting Started

Step 11. Verify connection, configuration, and data transfer using 

SEL-2032 commands 

WHO

, 

MAP

, 

VIEW

, and 

STATUS

.

a. Verify that the relay is connected to the desired port and 

configured properly by issuing the 

WHO

 command.

The SEL-2032 responds to this command with some 
basic information about the SEL-2032 and a list of the 
devices and device identification strings associated with 
each port. In this case, the list shows that an SEL-351S 
is connected to Port 2.

*>>

WHO <Enter>

                                            Date: 11/19/01    Time: 14:56:16
FID=SEL-2032-R100-V0-Z000000-D20021222 FID=SLBT-2030-R103-V0-Z000000-D20010122

Port#  Device    Protocol   Parameters  Identification
1      Master    SEL        9600,8,2,N
2      SEL-351S  SEL        19200,8,2,N FEEDER 1
3      SEL IED   SEL        9600,8,2,N
4      SEL IED   SEL        9600,8,2,N
5      SEL IED   SEL        9600,8,2,N
6      SEL IED   SEL        9600,8,2,N
7      SEL IED   SEL        9600,8,2,N
8      SEL IED   SEL        9600,8,2,N
9      SEL IED   SEL        9600,8,2,N
10     SEL IED   SEL        9600,8,2,N
11     SEL IED   SEL        9600,8,2,N
12     SEL IED   SEL        9600,8,2,N
13     SEL IED   SEL        9600,8,2,N
14     SEL IED   SEL        9600,8,2,N
15     SEL IED   SEL        9600,8,2,N
16     SEL IED   SEL        9600,8,2,N
17     SEL-2701  Ethernet   VTm:HS,CTl:HS,TIm:S,SBt:S
F*     Master    SEL        9600,8,2,N

*>>

Figure 2.10

Issue the WHO Command to Verify Relay Port Connection

The displayed response to the 

WHO

 command also 

identifies that Master port currently in use by placing an 
asterisk (*) next to its port number, Port F in the current 
example.

b. Issue the command 

MAP 2

 to verify the location and 

type of data being collected on Port 2 of the SEL-2032.

The SEL-2032 responds with a database map of the 
Port 2 data regions (see 

Figure 2.11

). This map shows 

that meter data are being collected in Port 2 region D1, 
which is associated with Port 2 Message 1. The B in 
front of METER indicates that the SEL-2032 is 
receiving binary, or Fast Meter, data from the 
SEL-351S. You can refer to the specific region by the 
region name, D1, or the data name, METER.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Edge-Core SDW100 Quick Start Manual preview
SDW100
Бренд: Edge-Core Страницы: 7
ForeScout CounterACT Quick Installation Manual preview
CounterACT
Бренд: ForeScout Страницы: 28
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Бренд: LSI Страницы: 3
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Бренд: ICP DAS USA Страницы: 8
ZALMAN CNPS7700 LED User Manual preview
CNPS7700 LED
Бренд: ZALMAN Страницы: 9
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Бренд: Sans Digital Страницы: 9
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Бренд: Advantech Страницы: 96
Laser UDC CARD User Manual preview
UDC CARD
Бренд: Laser Страницы: 4
Adaptec Serial Attached SCSI (SAS) Expander Card Installation And User Manual preview
Serial Attached SCSI (SAS) Expander Card
Бренд: Adaptec Страницы: 26
Digi 9P 9360/9750 User Manual preview
9P 9360/9750
Бренд: Digi Страницы: 75
Optus Ultra WiFi Booster Quick Manual preview
Ultra WiFi Booster
Бренд: Optus Страницы: 8
Pilz PNOZ mc3p Operating Instructions Manual preview
PNOZ mc3p
Бренд: Pilz Страницы: 12
Cypress Semiconductor CY7C027AV Specification Sheet preview
CY7C027AV
Бренд: Cypress Semiconductor Страницы: 18
Multitech MTDOT-868 Series Developer'S Manual preview
MTDOT-868 Series
Бренд: Multitech Страницы: 60
WIN Enterprises PL-83300 User Manual preview
PL-83300
Бренд: WIN Enterprises Страницы: 25
Delta Electronics Suppression Inductors LFZ24H Specification Sheet preview
Suppression Inductors LFZ24H
Бренд: Delta Electronics Страницы: 1
Tektronix 7B87 Instruction Manual preview
7B87
Бренд: Tektronix Страницы: 143
Boardcon Embedded Design EM3568 User Manual preview
EM3568
Бренд: Boardcon Embedded Design Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды