manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.11

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Settings

Automatic Message (SET A) Settings

setting the SEL-2032 to the lowest likely connection rate, typically 2400 baud. 
Alternatively, you can enable RTS/CTS or XON/XOFF flow control between 
the SEL-2032 and the modem.

To use hardware flow control, set RTS_CTS = Y on the modem port. Only use 
this setting if the RTS and CTS control lines are wired between the SEL-2032 
and the modem. The modem should default to use hardware flow control.

Alternatively, to use software flow control, set XON_XOFF=Y on the modem 
port and modify the MSTR setting to enable XON/XOFF handshaking within 
the modem. Refer to your modem data sheet to determine the appropriate code 
for your modem.

Many external modems do not behave well if they receive non-modem 
messages while they are not connected. For this reason, you should connect 
the Data Carrier Detect output of the modem to the SEL-2032 so 
transmissions to the modem can be prevented. If you have the modem 
connected to Port 1 or 9 of an SEL-2032, you can connect DCD and RTS/CTS 
flow control signals to the SEL-2032. If you are connected to any other port of 
a SEL-2032, connect the modem DCD output to the CTS input of the 
SEL-2032 and set CD_CTS to Yes. Of course, with this connection you will 
not be able to use RTS/CTS flow control.

Another thing to consider when using modems is how to terminate the 
connection. If you simply hang up, the SEL-2032 is left in whatever state you 
were in. This could be a state to which you cannot call back. To avoid this, you 
should do two things:

➤

When a modem is on a Master port, always exit transparent 
connections and issue the 

QUIT

 command to terminate the 

connection. This way, you always leave the SEL-2032 in a 
known state.

➤

Set the port TIMEOUT setting to something other than 0. If 
you do leave the SEL-2032 in an undesired state, it will return 
to a basic Access Level 0 state after the TIMEOUT time, as if a 

QUIT

 command had been issued.

Automatic Message (SET A) Settings

Use the 

SET A

 command to set the SEL-2032 to:

➤

Automatically buffer unsolicited messages the SEL-2032 
receives.

➤

Automatically print those unsolicited messages, and clear the 
buffer after printing if you desire.

➤

Automatically issue operate messages based on operating 
elements.

➤

Automatically collect Sequential Events Recorder (SER) data.

➤

Automatically collect synchrophasor data from SEL IEDs.

➤

Define startup strings for connected devices so the SEL-2032 
can communicate automatically with those devices.

➤

Create messages to send to other devices and define conditions 
that trigger those messages (messages are commands, data, or 
both).

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Magnat Audio MC 200 Faq preview
MC 200
Бренд: Magnat Audio Страницы: 2
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Бренд: Yamaha Страницы: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Бренд: Yamaha Страницы: 5
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Бренд: Garland Страницы: 6
Cypress Semiconductor CY7C1034DV33 Specification Sheet preview
CY7C1034DV33
Бренд: Cypress Semiconductor Страницы: 9
Automationdirect.com CLICK PLUS C2-02CPU Quick Start Manual preview
CLICK PLUS C2-02CPU
Бренд: Automationdirect.com Страницы: 10
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Бренд: ADTRAN Страницы: 2
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Бренд: Intel Страницы: 105
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Бренд: Stahl Страницы: 2
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Бренд: swiftech Страницы: 2
Buffalo AirStation G54 WLA2-G54 Quick Setup Manual preview
AirStation G54 WLA2-G54
Бренд: Buffalo Страницы: 8
Xilinx ML506 Quick Start Manual preview
ML506
Бренд: Xilinx Страницы: 29
Renesas R0E424270CFLE0 User Manual preview
R0E424270CFLE0
Бренд: Renesas Страницы: 4
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Бренд: Broadband Products Страницы: 16
Cutting Edge Unity AM Manual preview
Unity AM
Бренд: Cutting Edge Страницы: 92
Lanner HMB-6110 User Manual preview
HMB-6110
Бренд: Lanner Страницы: 43
Tektronix 7B87 Instruction Manual preview
7B87
Бренд: Tektronix Страницы: 143
AMD B59 User Manual preview
B59
Бренд: AMD Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды