manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

1.8

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Introduction and Specifications

Integration With the SEL-2032

Benefits of the 
SEL-2032 
Solution

Supports Multiple Data Consumers

The elegance of the SEL solution is the capability of the SEL-2032 to supply 
independent data or connections to different data consumers. For example, the 
data that you send to the SCADA system may be different than the data that 
you send to the HMI. The protocol and physical interface may also be 
different. Rather than connecting each system to the IEDs, you can collect 
data once from the IEDs and then prepare a concentrated, aggregated, 
independent data set for each data consumer.

Insulates IEDs From Integration Issues

When you use the SEL-2032, you perform many integration tasks and provide 
integration interfaces to the SEL-2032 rather than directly to the IEDs. This 
means that you have the best possible chance of leaving the IEDs undisturbed 
as your integration system evolves or changes.

For example, the field of substation integration is changing rapidly. The 
SEL-2032 allows you to integrate a system today and provide serial links to 
data consumers. In the future you can upgrade the SEL-2032 to provide 
additional protocols or install a communications card and add new 
connections without disturbing the IEDs. This is a key concern if the 
alternative system would require upgrading and recomissioning protection 
functions within IEDs in order to enhance your integration system.

You can also use the SEL-2032 to provide high-speed network connectivity 
rather than pay for it on each individual device. This means that your system 
will be much more economical and lets you take advantage of existing serial 
EIA-232 IEDs rather than replacing IEDs when upgrading a system.

Improves System Performance

When you replace a multidrop network with the SEL-2032, the SCADA data 
reaches the RTU or SCADA master more quickly. The reason is that the star 
network collects data from all IEDs in parallel rather than round-robin polling.    
Testing with an example system shows the difference. For a substation with 
seven IEDs, the data latency (time from field event to data available in master 
device) from the IED to an HMI is 1.5 seconds for a multidrop network and 
1.1 seconds for an SEL-2032 star network.

Scales to Substation Size

The number of ports on a single SEL-2032 is not a limit to the size of the 
system that you can construct. The SEL-2032 contains special features that 
allow multitiered systems such as the one shown in 

Figure 1.6

 to let you 

integrate large numbers of station IEDs.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Бренд: D-Link Страницы: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Бренд: D-Link Страницы: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Бренд: D-Link Страницы: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 97
3Com 3C16080 Important Information preview
3C16080
Бренд: 3Com Страницы: 2
3Com 3C421600A Quick Setup Manual preview
3C421600A
Бренд: 3Com Страницы: 74
3Com 3C421600A Installation Manual preview
3C421600A
Бренд: 3Com Страницы: 6
Abus TVVR36500 User Manual preview
TVVR36500
Бренд: Abus Страницы: 60
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Бренд: IEI Technology Страницы: 3
Belkin F5D9001 Series Manual preview
F5D9001 Series
Бренд: Belkin Страницы: 72
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Бренд: Riverbed Страницы: 38
Zoom 4412A User Manual preview
4412A
Бренд: Zoom Страницы: 48
Cromemco 32K Bytesaver Instruction Manual preview
32K Bytesaver
Бренд: Cromemco Страницы: 46
Verizon Wireless PC 3220 Owner'S Manual preview
PC 3220
Бренд: Verizon Wireless Страницы: 39
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Бренд: C-Com Страницы: 148
NC-link NC-AP111 User Manual preview
NC-AP111
Бренд: NC-link Страницы: 20
Arduino ABX00061 Reference Manual preview
ABX00061
Бренд: Arduino Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды