manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.4

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Settings

Port Configuration (SET P) and Communication Settings

SETTLE2

Posttransmit RTS deassertion delay
(0–30000 ms). 

Delay between end of transmission and RTS deassertion for
Modbus and DNP3 protocols. See 

Section 9: Protocols

 for

reference information on Modbus and DNP3 protocols.

BUSY_DIS

Disable transmission of Modbus Busy 
(Y/N)

Disable Modbus ports from sending a busy response. This may be 
used with masters that do not tolerate a busy response from a slave 
device.

ADDRESS1

Address of Port 1 (1–247). 

Modbus device address 1–247, or OFF if no Modbus access desired. 
Similarly for ADDRESS2–16. See 

Section 9: Protocols

 for reference 

information on Modbus.

ADDRESS

DNP Address
(0–65534 or 0000h–FFFEh). 

Address of the SEL-2032. It must be unique from all other DNP3 
addresses on the connection. See 

Section 9: Protocols

 for an

explanation of the DNP3 protocol.

CLASS

Class for event data
(0 for no event data, 1, 2, 3). 

Enter the DNP3 class, 1–3, to reference SEL-2032 event data under. 
Enter 0 if you do not want any event data. See 

Section 9: Protocols

 

for an explanation of the DNP3 protocol.

16BIT

Use 16- or 32-bit default
variations for analog inputs (16/32). 

DNP3 analog input objects can use default variations 16 or 32-bits in 
size. Set this to 16 or 32-bit, based on which default you prefer. Gen-
erally 32-bit is preferable, because you get a better range, but if your 
master does not support 32-bit analog inputs, you must use 16-bit. 
See 

Section 9: Protocols

 for an explanation of the DNP3 protocol.

SO_TIMEOUT

Select/Operate time-out interval,
seconds (0.0–30).

Enter the maximum allowable time between DNP3 function
codes for Select and Operate. If an Operate command follows the 
Select command by more than this time-out, the operation will not 
occur. Set based on worst-case timing of your master. See 

Section 9: 

Protocols

 for an explanation of the DNP3 protocol.

DL_CONFIRM

Number of data-link retries
(0 for no confirmation, 1–15).

Set to 0 to disable DNP3 data-link confirmation. Otherwise, set to the 
number of retries you want the DNP3 data-link to use. See 

Section 9: 

Protocols

 for an explanation of the DNP3 protocol.

DL_TIMEOUT

Data Link Time-out
(0–5000 milliseconds).

Set to the worst-case DNP3 data-link acknowledge time of your
master. When using DNP3 data-link confirmation, this is the time the 
SEL-2032 waits before assuming there is no confirmation and 
resending the message. See 

Section 9: Protocols

 for an explanation 

of the DNP3 protocol.

MIN_DELAY

Minimum Delay from DCD
to transmission (0–1000 msec).

This is the minimum delay the SEL-2032 waits from DCD going 
away or from the last character being received before initiating data 
transmission. See 

Section 9: Protocols

 for an explanation of the 

DNP3 protocol.

MAX_DELAY

Maximum Delay from DCD
to transmission (0–1000 msec).

This is the maximum delay the SEL-2032 waits from DCD going 
away or from the last character being received before initiating data 
transmission, if there is a transmission pending. Set this to something 
bigger than MIN_DELAY to cause some randomness in the time at 
which it attempts to transmit again. In a system with unsolicited
messaging, this helps reduce the likelihood of repeated collisions. 
See 

Section 9: Protocols

 for an explanation of the DNP3 protocol.

REPORT_ON

Percent of Full-Scale
Change to Report on (0–100%). 

This setting determines at what point counter and analog input events 
are declared. Set this to the percent of the full-scale that you want 
events reported on. With the default size set to 16-bit, full scale is +/- 
32767. See 

Section 9: Protocols

 for an explanation of the DNP3

protocol.

UNSOL_REP

Allow Unsolicited Reporting (Y/N). 

Set to Yes to enable unsolicited DNP3 event reporting or No to dis-
able such reporting. See 

Section 9: Protocols

 for an explanation of 

the DNP3 protocol.

Table 7.1

Port Configuration (SET P) Settings Information 

 (Sheet 2 of 5)

Setting

Comment

Description

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

EAW MX250 Owner'S Manual preview
MX250
Бренд: EAW Страницы: 10
NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Бренд: NEC Страницы: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Бренд: NEC Страницы: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Бренд: NEC Страницы: 2
Patton electronics 1084 Installation And Operation Manual preview
1084
Бренд: Patton electronics Страницы: 16
Vivotek NR8401 User Manual preview
NR8401
Бренд: Vivotek Страницы: 136
IBA ibaFOB-4i-X Manual preview
ibaFOB-4i-X
Бренд: IBA Страницы: 33
NEC P401-TMX4D User Manual preview
P401-TMX4D
Бренд: NEC Страницы: 2
XMOS XC-2 Quick Start Manual preview
XC-2
Бренд: XMOS Страницы: 6
XNET INS2000 Install Manual preview
INS2000
Бренд: XNET Страницы: 17
ETC Power Control Processor Configuration Manual preview
Power Control Processor
Бренд: ETC Страницы: 64
Intel Core 2 Quad Q9400 Product Brief preview
Core 2 Quad Q9400
Бренд: Intel Страницы: 2
Avaya PARTNER PC CARD Installation Instructions preview
PARTNER PC CARD
Бренд: Avaya Страницы: 4
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Бренд: Delta Electronics Страницы: 1
Supersonic Franky Instruction Manual preview
Franky
Бренд: Supersonic Страницы: 46
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Бренд: Digital Equipment Страницы: 90
ZALMAN CNPS8900 Series User Manual preview
CNPS8900 Series
Бренд: ZALMAN Страницы: 10
netsys NH-310S User Manual preview
NH-310S
Бренд: netsys Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды