Schweitzer Engineering SEL-2032 Скачать руководство пользователя страница 312

Страница: 312 / 354

10.2

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Testing and Troubleshooting

Self-Tests

The SEL-2032 continually runs the following self-tests. Any test failure
causes an alarm to be latched and the status report to be issued on Port F.

RAM.

The SEL-2032 continually performs read-write test of RAM, both

local and shared.

Code Flash.

The SEL-2032 continually computes and checks a checksum

of ROM.

EEPROM/Archive Flash.

The SEL-2032 continually validates data blocks

using checksums.

Power Supply.

Threshold comparators (+/– 15 V) are continually checked

for tolerance.

Troubleshooting

Power
System Problems

Table 10.2

describes typical SEL-2032 power system problems and solutions.

Communications
Problems

Refer to

Table 10.3

for troubleshooting some basic communications problems.

Table 10.2

Power System Problems

Symptom

Probable Cause

Corrective Action

All front-panel LEDs
remain dark when LED
TEST button is pressed.

No power to
rear-panel power terminals.

Internal power
supply defective.

Supply power to
rear-panel power terminals.

Remove power
and contact the factory.

+5 Vdc not supplied
to pin 1 of rear-panel
communication port(s).

Jumper(s) not
installed on main board.

See

Jumper Settings on

page 2.1

Table 10.3

Communications Problems

(Sheet 1 of 2)

Symptom

SEL-2032 does not communicate with PC.

Probable Cause

Serial cable damaged or wrong cable connected.

Corrective Action

Inspect the cabling for damage and proper connection.

Symptom

SEL-2032 does not communicate with PC.

Probable Cause

SEL-2032 baud rate default jumper installed.

Corrective Action

Set the PC terminal to 2400 baud to communicate with the
SEL-2032.

Using the

SET

command, set the SEL-2032 baud rate.

Access the main board. Refer to

Jumper Settings on page 2.1

Remove jumper

J17 A. Place the jumper on one pin of the

connector for safekeeping.

Set the baud rate of the PC terminal to match the SEL-2032.

Cycle SEL-2032 power and reconnect.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации

Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды