manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.27

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Settings

User-Defined (SET U) Commands

that you configure the Fast Message client to periodically issue Enable 
Unsolicited SER requests to an IED to restart the reporting of unsolicited SER 
in case of loss of communications to the IED.

Transparent Connections

Before making a transparent connection, the SEL-2032 checks the NOCONN 
bit on the Slave port.  If the bit is asserted, the attempted transparent 
connection is immediately aborted.  In addition, the NOCONN bit blocks 
transparent connections on every mechanism: 

PORT

 command, user-defined 

transparent connect string (TRANS in 

SET U

), and Distributed Port Switch 

Protocol (LMD).  If the PORT command is attempted, the following error 
message is displayed: 

Unable to connect, Port x blocked by NOCONN bit.

Virtual Terminal Connections

The SEL-2032 shall check the NOCONN bit before allowing any Virtual 
Terminal connection.

When the VT connection is initiated by a SEL-2032 user via the 

PORT

 

command, the SEL-2032 shall function exactly as described above for 
transparent connections.

When the protocol card initiates a VT connection, the SEL-2032 shall reject 
the connection as long as the NOCONN bit is asserted.

User-Defined (SET U) Commands

Use the 

SET U

 command to:

➤

Create user-defined commands that the SEL-2032 recognizes 
and obeys.

➤

Enable handling of a recognized, but unsolicited, SEL relay 
auto-message.

➤

Control the SEL-2032 command set.

User-defined commands allow the SEL-2032 to recognize unsolicited inputs. 
You can create up to 11 user-defined commands for any Master port, including 
8 general-purpose and 3 special-purpose commands. You can create up to 4 
general-purpose user-defined commands on SEL IED and other IED ports.

The SEL-2032 has a predefined command set (e.g., 

SHOW

, 

VIEW

, 

SET

) that 

allows you to control, interrogate, and set the SEL-2032 functions from your 
computer. If a port is connected to an unattended device (e.g., an RTU or 
substation computer), the SEL-2032 predefined command set may be 
supplemented or replaced by user-defined commands that are appropriate for 
the device and function. They are called user defined because you define the 
command string and the action performed by the SEL-2032 when the 
command is received by the SEL-2032. These commands are available at all 
access levels.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Бренд: National Instruments Страницы: 85
YASKAWA A1000 Series Installation Manual preview
A1000 Series
Бренд: YASKAWA Страницы: 34
Q-See QC814 Specifications preview
QC814
Бренд: Q-See Страницы: 2
Falcon 4G COMBO User Manual preview
4G COMBO
Бренд: Falcon Страницы: 24
Acces I/O products MPCIE-ICM232-2 Hardware Manual preview
MPCIE-ICM232-2
Бренд: Acces I/O products Страницы: 5
Enertronica Santerno SINUS H PROFInet User Manual preview
SINUS H PROFInet
Бренд: Enertronica Santerno Страницы: 34
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Бренд: Longshine Страницы: 27
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Бренд: Danville Signal Processing Страницы: 35
Lanner FW-7551 User Manual preview
FW-7551
Бренд: Lanner Страницы: 38
Advantech 3718HG User Manual preview
3718HG
Бренд: Advantech Страницы: 68
Navitar 1-62645 Dimensional Drawing preview
1-62645
Бренд: Navitar Страницы: 1
CompuLab CL-SOM-AM57 Series Reference Manual preview
CL-SOM-AM57 Series
Бренд: CompuLab Страницы: 79
Renesas M34502T-MCU User Manual preview
M34502T-MCU
Бренд: Renesas Страницы: 40
Waveshare High-Precision AD/DA Board User Manual preview
High-Precision AD/DA Board
Бренд: Waveshare Страницы: 8
ETAS ES1337.2 User Manual preview
ES1337.2
Бренд: ETAS Страницы: 29
Intellinet 720564 Instructions preview
720564
Бренд: Intellinet Страницы: 2
Riverbed SteelCentral NetExpress 470 Upgrade And Maintenance Manual preview
SteelCentral NetExpress 470
Бренд: Riverbed Страницы: 140
DAPAudio D2081 Manual preview
D2081
Бренд: DAPAudio Страницы: 33

Бренды по названию

Популярные бренды

Загрузить еще бренды