manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Section 5

Message Strings

Introduction

This section provides information about the characters, special sequences of 
characters, and predefined strings that you can use in a number of SEL-2032 
settings. A blue pull-out card at the end of the book contains a summary list of 
special characters and predefined strings.

Overview

A string is a sequence of characters that make up part, or all, of a message 
command or identifier label. Each character may be an ASCII printable 
character or any 8-bit code that represents a nonprintable character. You use 
these strings in the following ways:

➤

Device and Port IDs, termination strings, and modem startup 
strings in Port configuration using the 

SET P

 command.

➤

Startup sequence for an IED and message strings in auto-
messages using the 

SET A

 command.

➤

User-defined commands and responses using the 

SET U

 

command.

NOTE

: You should avoid using LMD 

prefix characters in Master port user-
defined commands. For an 
explanation of LMD and a list of LMD 
prefix characters see 

Section 9: 

Protocols

.

Message strings consist of literal characters, special sequences, and 
predefined strings. Literal characters include both ASCII printable and 
nonprintable characters. Special sequences are strings that are interpreted to 
have a special meaning when they are used, such as dial a particular phone 
number, or output a specified set of database data. Predefined strings are used 
with SEL IEDs to represent certain predefined operations, such as 20METER 
means collect meter data in best method available for attached device. The 
following sections further describe these types of message sequences.

Literal Characters

Message strings typically contain some literal characters. These consist of 
both ASCII printable characters and nonprintable characters. Printable 
characters (except ‘\’) are entered into a string by directly entering the 
character (depressing the key for that character on your keyboard). You can 
also enter any character based on its 8-bit code. To enter a nonprintable 
character (or special sequence strings) using printable characters, you must 
use a special sequence to indicate that you are entering something other than a 

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Dahua DHI-NVR5224-24P-4KS2 Quick Start Manual preview
DHI-NVR5224-24P-4KS2
Бренд: Dahua Страницы: 24
Paradox ZX32D Manual preview
ZX32D
Бренд: Paradox Страницы: 4
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Бренд: Quantum Страницы: 12
STONEFLY DR365V-2404 Setup Manual preview
DR365V-2404
Бренд: STONEFLY Страницы: 48
Fostex DE-1 Service Manual preview
DE-1
Бренд: Fostex Страницы: 20
Zonet ZUN2200 Quick Installation Manual preview
ZUN2200
Бренд: Zonet Страницы: 2
Avolites Titan One Quick Start Manual preview
Titan One
Бренд: Avolites Страницы: 24
Tandy 26-3814 Operation Manual preview
26-3814
Бренд: Tandy Страницы: 24
Disc Makers Reflex10 User Manual preview
Reflex10
Бренд: Disc Makers Страницы: 38
Hauppauge WinTV USB Installation And Reference Manual preview
WinTV USB
Бренд: Hauppauge Страницы: 55
Alcatel-Lucent Service Aggregation Router 7705 Installation Manual preview
Service Aggregation Router 7705
Бренд: Alcatel-Lucent Страницы: 20
Hanwha Techwin WISENET XRN-1610 User Manual preview
WISENET XRN-1610
Бренд: Hanwha Techwin Страницы: 88
Adaptec Ultra Wireless AWN-8030 User Manual preview
Ultra Wireless AWN-8030
Бренд: Adaptec Страницы: 57
IBASE Technology ET880 Series User Manual preview
ET880 Series
Бренд: IBASE Technology Страницы: 64
Alvarion BreezeACCESS II System Manual preview
BreezeACCESS II
Бренд: Alvarion Страницы: 324
Fujitsu 467 Manual preview
467
Бренд: Fujitsu Страницы: 36
3Egreen CM01-01 Instructions For Use Manual preview
CM01-01
Бренд: 3Egreen Страницы: 10
Crestron HDMI Input Card DMC-HD Specifications preview
HDMI Input Card DMC-HD
Бренд: Crestron Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды