manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

1.5

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Introduction and Specifications

Integration With the SEL-2032

Integrated
Substation
Functions

In order to design an integrated substation, you must start by defining the jobs 
that you wish the integrated substation system to perform. The list below 
summarizes the most popular functional categories that integrated systems 
perform:

➤

Remote status and measurement data collection and control 
for SCADA.

 Collecting data from the IEDs and additional 

inputs for display to operators through a SCADA system. 
Coordinating controls from SCADA with local permissives.

➤

Local HMI (Human Machine Interface).

 Display of local 

status and measurement and control often used for local 
maintenance operation or backup local operation in the event of 
a SCADA failure.

➤

Time synchronization.

 Synchronizing the time clocks of the 

IEDs so that time referenced data can be compared between 
IEDs.

➤

Distributed automation.

 Basic station automation and control 

performed in IEDs rather than a central automation processing 
platform like an RTU or PLC (Programmable Logic 
Controller). This may also include dedicated control such as 
capacitor bank control.

➤

Engineering and maintenance information management.

 

The collection, storage, and communication of historical, event, 
and collected data that are used for fault analysis, maintenance 
scheduling, system planning, and other engineering tasks. For 
example, fault records and circuit breaker monitoring reports 
are collected by protective relays and made available for 
engineering through the system.

Integration With the SEL-2032

The SEL-2032 combined with SEL relays, non-SEL IEDs, and SEL software 
solutions forms a comprehensive approach to substation integration. If we 
consider the five basic functional categories listed in 

Integrated Substation 

Functions on page 1.5

 and construct a system out of conventional 

components, we start with the system shown in 

Figure 1.3

. In 

Figure 1.4

 we 

use a multidrop network to connect the IEDs to the RTU and provide basic 
control and SCADA monitoring functions.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

EAW MX250 Owner'S Manual preview
MX250
Бренд: EAW Страницы: 10
3Com 3CRWB6096 Quick Start Manual preview
3CRWB6096
Бренд: 3Com Страницы: 8
Eaton INDGW-X2 Manual preview
INDGW-X2
Бренд: Eaton Страницы: 10
LAWO edge User Manual preview
edge
Бренд: LAWO Страницы: 154
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Бренд: Lattice Semiconductor Страницы: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Бренд: Lattice Semiconductor Страницы: 13
Profile LS901-E1 Instruction Manual preview
LS901-E1
Бренд: Profile Страницы: 6
Blackrock Microsystems Cerebus Instructions For Use Manual preview
Cerebus
Бренд: Blackrock Microsystems Страницы: 27
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Бренд: LGC wireless Страницы: 154
IDT DBP 7+4 User Manual preview
DBP 7+4
Бренд: IDT Страницы: 93
D3 DesignCore RVP-TDA3 Series Quick Start Manual preview
DesignCore RVP-TDA3 Series
Бренд: D3 Страницы: 34
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Бренд: Parker Страницы: 107
Kontron 50099 067 User Manual preview
50099 067
Бренд: Kontron Страницы: 42
ICOP Technology BF01 User Manual preview
BF01
Бренд: ICOP Technology Страницы: 34
LaCie FireWire 800 ExpressCard 34 Quick Install Manual preview
FireWire 800 ExpressCard 34
Бренд: LaCie Страницы: 24
Patton electronics ipRocketLink IAD 3086 Quick Start Manual preview
ipRocketLink IAD 3086
Бренд: Patton electronics Страницы: 12
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Бренд: Bridgeworks Страницы: 56
Paradyne 8310 MVLt User Manual preview
8310 MVLt
Бренд: Paradyne Страницы: 108

Бренды по названию

Популярные бренды

Загрузить еще бренды