manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

9.7

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Protocols

SEL Fast Message Protocol

The SEL-2032 will automatically send the “Enable Unsolicited Data 
Transfer” message (function code 0x20) to the attached SEL IED along with 
the rate value. This message instructs the SEL IED to begin sending UW 
Messages (synchrophasor data) to the SEL-2032 at the specified rate. If the 
attached IED does not support UW message transmission or the specified 
message rate, the setting will fail to enable synchrophasor data transmission. 
Note that the SEL-421, SEL-451, and SEL-734 devices only support an 
SP_RATE of 60 when transmitting synchrophasor data to the SEL-2032. The 
SEL-311 series relays and most SEL-351 series relays support all valid 
message rates. It is the responsibility of the user to choose a valid UW 
message rate (selected by SP_RATE) supported by the attached SEL IED. 
Refer to the appropriate SEL IED instruction manual for supported data rates.

Fast Message Synchrophasor Processing

When UW message collection is enabled and the IED supports UW message 
transmission, the SEL-2032 will periodically attempt to enable UW message 
transmission every five minutes. This ensures that if the connected SEL IED 
ever stops sending UW messages (for example, in the event of a power 
failure), the SEL-2032 will re-enable them after a maximum interval of five 
minutes.

In order to disable UW Message collection, the user must set SP_RATE to 
“N” (None). The SEL-2032 will automatically send a “Disable Unsolicited 
Data Transfer” message to the attached SEL IED.

When necessary, the SEL-2032 will send a “Disable Unsolicited Data 
Transfer” message to the attached SEL IED, disabling UW messages. This 
includes during port settings changes, initiation of transparent 
communications, reconfiguration, etc. Once the SEL-2032 is able to receive 
UW messages, the SEL-2032 will automatically send an “Enable Unsolicited 
Data Transfer” message (along with the rate value) to reenable data collection.

The IED must respond to every Enable or Disable message the SEL-2032 
sends within 1/2 second. If it does not receive a response, the SEL-2032 will 
send the message up to three times more (for a total of four attempts). After 
making the fourth attempt, the SEL-2032 will return to processing normal 
communications traffic.

Note that the SEL-2032 will process all UW messages from a lower-tier 
device whether or not UW messages are enabled or disabled via this new 
automatic setting.

Multitiered 
SEL-2032 
Applications

If you have more than 16 IEDs in your substation, you can collect data with a 
multitiered SEL-2032 architecture similar to that shown in 

Figure 9.2

. With 

this architecture, the connection between the SEL-2032 and the relays uses the 
Fast Message protocol to convey measurements, control messages, and collect 
SER information. As with connections to other SEL IEDs, the message and 
communication configuration is mostly automated by the auto-configuration 
process. You can pass data between the SEL-2032 and the relays (in either 
direction) using the “\W” automatic message described in 

Section 7: Settings

.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

ZALMAN CNPS17X User Manual preview
CNPS17X
Бренд: ZALMAN Страницы: 20
XMG OASIS Disassembly Procedure preview
OASIS
Бренд: XMG Страницы: 5
NAD M10 Quick Setup Manual preview
M10
Бренд: NAD Страницы: 2
Ebyte E43-900T13S3 Manual preview
E43-900T13S3
Бренд: Ebyte Страницы: 8
Patton electronics 1090 Service Manual preview
1090
Бренд: Patton electronics Страницы: 8
Ublox NEO-D9S Quick Start Manual preview
NEO-D9S
Бренд: Ublox Страницы: 17
Z3 Technology Z3-DM8168-PCI-RPS Manual preview
Z3-DM8168-PCI-RPS
Бренд: Z3 Technology Страницы: 20
Z3 Technology Z3-DM8107-SDI2-RPS User Manual preview
Z3-DM8107-SDI2-RPS
Бренд: Z3 Technology Страницы: 75
Z-Wave USB Dongle User Manual preview
USB Dongle
Бренд: Z-Wave Страницы: 13
Maxim DS5001FP Specification Sheet preview
DS5001FP
Бренд: Maxim Страницы: 26
Clavister NetWall W20A Getting Started Manual preview
NetWall W20A
Бренд: Clavister Страницы: 89
Orban OPTIMOD 6300 Operating Manual preview
OPTIMOD 6300
Бренд: Orban Страницы: 255
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Бренд: Dialogic Страницы: 2
Lanner ICS-P570 User Manual preview
ICS-P570
Бренд: Lanner Страницы: 63
EK-Quantum Momentum ROG Strix X570-E D-RGB User Manual preview
Momentum ROG Strix X570-E D-RGB
Бренд: EK-Quantum Страницы: 10
NXP Semiconductors RDGD3160I3PH5EVB User Manual preview
RDGD3160I3PH5EVB
Бренд: NXP Semiconductors Страницы: 21
Renesas R0E424270CFLE0 User Manual preview
R0E424270CFLE0
Бренд: Renesas Страницы: 4
Fast FV3000-W2K Instruction Manual preview
FV3000-W2K
Бренд: Fast Страницы: 66

Бренды по названию

Популярные бренды

Загрузить еще бренды