manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

8.18

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Serial Port Communications and Commands

Command Set

Port Switch Protocol, the connection is dropped when you issue the 

QUIT

 

command. If you are connected to the port through a dial-up modem, the 
SEL-2032 will hang up the modem when it receives a 

QUIT

 command.

SER

The SER command (Access Level 1) displays SER region data. The command 
has the following format:

SER 

x

 [BL] | [

m

] [

n

] | [C | CA | R]

where:

➤

x

 is either a port number, GLOBAL or ALL.

➤

BL displays the labels of the SER points for the specified port

➤

m

 is the number of most recent records to display–default is the 

last 20

➤

n

, if supplied with 

m

, defines a range of records to display

➤

C or R clears the SER records for the selected port

➤

CA clears all of the SER records in the SEL-2032. When CA is 
selected, no port number may be specified.

Variations of the SER command are detailed in 

Table 8.3

.

Examples of the 

SER

 command are shown in 

Figure 8.27

.

*>>

SER 2 <Enter>

<STX>
Port 2,  SER Data 
#      DATE        TIME           ELEMENT              STATE
9    07/23/1996  08:15:32.123     52A                Deasserted
8    07/23/1996  08:15:31.123     52A                Asserted
7    07/23/1996  08:15:30.123     52A                Deasserted
6    07/23/1996  08:15:29.123     52A                Asserted
5    07/23/1996  08:15:28.123     52A                Deasserted
4    07/23/1996  08:15:27.123     52A                Asserted
3    07/23/1996  08:15:26.123     52A                Deasserted
2    07/23/1996  08:15:25.123     52A                Asserted
1    07/23/1996  08:15:24.123     52A                Deasserted
<ETX>
*>>

Figure 8.27

SER Command

The example in 

Figure 8.28

 uses the BL parameter with the 

SER

 command.

Table 8.3

Variations of the SER Command

Command

Action

Format

Application

SER

Display the SER records 
currently in the SEL-2032.

SER 1

SER GLOBAL

SER 1 5 11 

Display the SER records in the port 1 SER region.

Display the GLOBAL region SER data.

Display records 5–11 from port 1 SER region.

SER 

n

 BL

Display the SER data 
points and their index.

SER 1 BL

Display the SER points
collected from the attached
IED and their relative index in the SER region.

SER 

n

 C

Clear SER records.

SER 1 C or SER 1 R SER CA 

Clear port 1 SER records.
Clear all SEL-2032 SER records.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

B2 ABB2050 Instruction Manual preview
ABB2050
Бренд: B2 Страницы: 52
SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Бренд: SAF Страницы: 30
IBM Power System H924 Installing Instructions preview
Power System H924
Бренд: IBM Страницы: 48
Renesas R0E001000ACB00 User Manual preview
R0E001000ACB00
Бренд: Renesas Страницы: 4
Ubiquiti EdgeSwtch 5XP Quick Start Manual preview
EdgeSwtch 5XP
Бренд: Ubiquiti Страницы: 13
TP-Link VIGI NVR1004H-4P Quick Installation Manual preview
VIGI NVR1004H-4P
Бренд: TP-Link Страницы: 2
Logicube ZCLONE User Manual preview
ZCLONE
Бренд: Logicube Страницы: 56
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Бренд: CAME Страницы: 32
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Бренд: Digital Equipment Страницы: 90
Commell MP-6802 User Manual preview
MP-6802
Бренд: Commell Страницы: 18
IBM SA23-1325-01 Installation And Using Manual preview
SA23-1325-01
Бренд: IBM Страницы: 44
Ezquest Boa K16766 User Manual preview
Boa K16766
Бренд: Ezquest Страницы: 65
ICP DAS USA ET-7017-10 Quick Start Manual preview
ET-7017-10
Бренд: ICP DAS USA Страницы: 8
TRENDnet TEW-221PC User Manual preview
TEW-221PC
Бренд: TRENDnet Страницы: 56
Behringer MU-A043666 Quick Start Manual preview
MU-A043666
Бренд: Behringer Страницы: 12
JETWAY 939GT2-Ultra Series User Manual preview
939GT2-Ultra Series
Бренд: JETWAY Страницы: 55
Korg EXBP-MP3 User Manual preview
EXBP-MP3
Бренд: Korg Страницы: 8
MSI MPG SEKIRA 500X Manual preview
MPG SEKIRA 500X
Бренд: MSI Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды