manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

9.10

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Protocols

Modbus RTU Protocol

Table 9.3

 contains a summary of Modbus mapping for the SEL-2032. The 

summary also contains a brief list of the capabilities of the SEL-2032 that are 
available with each data type. You must use the correct register references and 
Modbus function codes for the Modbus master you are using to access the 
data.

 

Sophisticated Modbus masters utilize standard Modbus register references and 
automatically create Modbus messages using Modbus function codes. For 
example, HMI drivers such as Wonderware

®

 InTouch

®

 require that you enter 

reference that includes the Modbus register reference. You can use the 
Modbus mapping listed in 

Table 9.3

 to create the correct Modbus reference. 

For example, the first register of the User region is F800h. If you wish to 
access this register as a holding register, convert to decimal (63488) and add 1 
and place the type identifier (4) before the number for a reference of 463489. 
There are additional examples and information about Modbus references in 

Function Codes on page 9.12

.

Modbus protocol compatibility facilitates connection to many Remote 
Terminal Units (RTU), and to most Programmable Logic Controllers (PLC) 
and PLC Networks.

Settings

From Port F or another master port, use the 

SET P 12

, 

SET P 14

, or 

SET P 16

 

command to set the device type to MASTER and the protocol to MODBUS. 
The SEL-2032 will prompt for the map style, device ID offset, and Modbus 
slave address for each of 18 ports. With the map type setting, you select 
between the default map which contains floating-point data and the integer-
only map. With the device ID offset setting, you can select an offset for the 

Input 
Register

3X

30001,
3099, 31023

16-bit analog 
input values

16-bit SEL-2032
database registers (use
2 consecutive registers
for floating point numbers)

Holding 
Register

4X

40001,
4099, 41023

16-bit
internal storage, 
16-bit analog 
output values

16-bit SEL-2032
database registers (use
2 consecutive registers
for floating point numbers)

Table 9.3

SEL Modbus Map Summary

Modbus Data 
Type

SEL Mapping

Use

Coil (0X)

See 

Table 9.5

Read status of global elements,
local elements, Relay Word bits,
and bits within User region registers

Control remote bits and breaker bits.

Input (1X)

See 

Table 9.5

Read status of global
elements, local elements, Relay Word
bits, and bits within User region registers.

Input 
Register (3X)

Automatic

Read automatic Modbus
map data. Use the 

MODMAP

 command; see 

Table 9.8

 to 

Table 9.13

 for examples.

Holding 
Register (4X)

SEL-2032 database 
address plus 1

Read any register
within the SEL-2032 on any port

Write data to SEL-2032 User region on any port.

Table 9.2

Modbus Data Types 

 (Sheet 2 of 2)

Modbus 
Data Type

Type

Examples

Modicon PLC 
Data Type

SEL Data Type

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

TE Connectivity InterReach Fusion ADCP-77-044 Manual preview
InterReach Fusion ADCP-77-044
Бренд: TE Connectivity Страницы: 236
Pima ZEL508 Installation Instructions preview
ZEL508
Бренд: Pima Страницы: 4
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Бренд: ekwb Страницы: 2
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Бренд: B&B Electronics Страницы: 4
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Бренд: Dialogic Страницы: 2
National Instruments Fieldpoint cFP-RTD-124 Operating Instructions Manual preview
Fieldpoint cFP-RTD-124
Бренд: National Instruments Страницы: 15
Hama 00039747 Operating Instruction preview
00039747
Бренд: Hama Страницы: 6
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Бренд: Jaycar Electronics Страницы: 2
Cytron Technologies SHIELD-2AMOTOR User Manual preview
SHIELD-2AMOTOR
Бренд: Cytron Technologies Страницы: 13
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Бренд: Balluff Страницы: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Бренд: MEMON Страницы: 2
Active Communications ACS express Quick Start Manual preview
ACS express
Бренд: Active Communications Страницы: 10
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Бренд: Alcatel-Lucent Страницы: 60
Crown PIP-AF Owner'S Manual preview
PIP-AF
Бренд: Crown Страницы: 7
Corsair Hydro H110 Quick Start Manual preview
Hydro H110
Бренд: Corsair Страницы: 10
NetBurner SBL2e User Manual preview
SBL2e
Бренд: NetBurner Страницы: 30
NEC N8154-25 User Manual preview
N8154-25
Бренд: NEC Страницы: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Бренд: Renesas Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды