Schweitzer Engineering SEL-2032 Скачать руководство пользователя страница 313

Страница: 313 / 354

10.3

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Testing and Troubleshooting

Troubleshooting

Symptom

SEL-2032 does not communicate with connected IED.

Probable Cause

Port and baud rate settings of PC may be incorrect.

Corrective Action

Set the port and baud rate settings of the PC terminal to match
the SEL-2032

If you do not know what the settings are, install the

baud rate jumper and then make the settings

Symptom

SEL-2032 does not communicate with connected IED.

Probable Cause

Serial cable damaged or wrong cable connected.

Corrective Action

Inspect the cabling for damage and proper connection. Make
sure appropriate cable is connected (see

Table 2.4

Symptom

SEL-2032 does not communicate with connected IED.

Probable Cause

Port settings do not match the IED settings.

Corrective Action

Using the

SET

command, set the port settings

to match those of the IED connected to the port.

Symptom

SEL-2032 does not communicate with connected IED.

Probable Cause

Port may be locked up due to hardware handshaking

Corrective Action

Reset IED and/or reset port settings
using

SET P

and accepting settings.

Symptom

SEL-2032 does not communicate with connected IED.

Probable Cause

Component failure. Port F LED(s) illuminates
but others do not illuminate when port is addressed.

Corrective Action

Remove power and contact the factory.

Symptom

No prompt.

Probable Cause

Incorrect baud rate.

Corrective Action

Verify baud rate in communication software.
Default baud rate for the SEL-2032 is 2400.

Symptom

SEL-2032

not accepting

REC

command

Probable Cause

Not in the SEL

BOOT

mode

Corrective Action

Enter

L_D

to get into the SEL

BOOT

mode. When in SEL

BOOT

mode, the prompt is an exclamation point.

Symptom

Protocol card not accepting

REC

command

Probable Cause

SEL-2032 and protocol card are not in the SEL

BOOT

mode

Corrective Action

Enter

L_D

to get into the SEL

BOOT

mode. When in SEL

BOOT

mode, the prompt is an exclamation point. Also see next problem to
force SEL

BOOT

mode.

Symptom

Unknown communication problem

Probable Cause

Incompatible firmware in SEL-2032

and protocol card.

2. Device not in SEL

BOOT

mode.

Corrective Action

Force SEL-2032 into SEL

BOOT

mode using the following

procedure:

Cycle Power on the SEL-2032 while depressing the LED TEST
button on the SEL-2032.

The SEL-2032 will enable with the default baud rate of 2400.

Table 10.3

Communications Problems

(Sheet 2 of 2)

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации

Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды