Schweitzer Engineering SEL-2032 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 354

background image

2.6

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Installation

Mounting and Connections

Port Isolators

SEL offers a data-line-powered isolator for use with EIA-232 ports and
metallic communication cables. The SEL-2910 Port Isolator also isolates
IRIG-B time code inputs on the same communication port. These isolators
break cable ground loops and are useful in existing applications of metallic
cables in switchgear. SEL does not recommend using port isolators for circuits
outside the control house. Fiber should be used in such applications. Refer to
SEL Application Guide AG2001-06,

Avoiding Magnetic Induction Issues in

Communication Cabling

, for detailed information.

Fiber-Optic
Cables

A benefit of applying the SEL-2032 is that as the hub of a star topology, it
enables low cost, point-to-point fiber-optic connections. The SEL-2800 family
of Fiber-Optic Transceivers connects directly to the serial port connectors on
the rear of the SEL-2032. Fiber-optic links improve safety by isolating the
equipment from hazardous and damaging ground-potential rise, eliminate
instrumentation system ground-loop problems, reduce susceptibility to RFI
and EMI, and allow longer signal paths than metallic EIA-232 connections.

Communication
Cables

Several of the most popular SEL communication cables available for your use
with the SEL-2032 are listed in

. For a complete list of SEL cables

and recommended applications, see the SEL-5801 Cable Selector software
available on the SEL Web site. Using an improper cable can cause numerous
problems, so you must be sure to specify the proper cable for the application.

Table 2.3

Serial Port Connector Pin Definitions

Pin

Ports 1–16

Port F

1

Various

a

a

Port 1, 9 = DCD; Port 2, 5-8, 10, 13, 15 = N/C; Port 3, 4, 11, 12, 14, 16 = N/C or +5 Vdc if
appropriate internal jumper is installed.

N/C

2

RXD

RXD

3

TXD

TXD

4

Various

b

b

Port 1-14, 16 = +IRIG-B Output; Port 15 = +IRIG-B Input or Output depending on internal
jumper configuration.

N/C

5, 9

GND

GND

6

Various

c

c

Port 1-14, 16 = -IRIG-B Output; Port 15 = -IRIG-B Input or Output depending on internal jumper
configuration.

N/C

7

RTS

RTS

8

CTS

CTS

Table 2.4

Communication Cables for Devices Attached to SEL-2032

(Sheet 1 of 2)

SEL

Cable #

Connect

SEL-2032 to:

Remote

Connector

(on cable)

Port Type

RTS/CTS

Supported

IRIG-B

Included

C234A

9-pin DTE devices:
Standard computer.
Use for SEL-2032
configuration.

DB-9S

DTE

no

no

C239

9-pin DTE devices
w/IRIG-B:
SEL-200/321
series relays

DB-9P,

DB-9P

DTE/

IRIG-B

yes

yes

Courtesy of NationalSwitchgear.com

«
...
50
51
52
53
54
...
»

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Univerge SV8100

Бренд: NEC Страницы: 44

Бренд: XDS Страницы: 99

Бренд: D-Link Страницы: 12

PCMCIA WIRELESS ASAPTER DWL-650

Бренд: D-Link Страницы: 5

PowerLine DHP-W611AV

Бренд: D-Link Страницы: 78

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Secure Site Manager 16

Бренд: Black Box Страницы: 16

Бренд: Alesis Страницы: 11

Бренд: NXP Semiconductors Страницы: 1202

Бренд: ZALMAN Страницы: 6

Бренд: FDI Страницы: 15

Suppression Inductors LFZ24H

Бренд: Delta Electronics Страницы: 1

Dablet DVP 5000

Бренд: DarbeeVision Страницы: 10

Бренд: QSC Страницы: 4

Бренд: Aegis Страницы: 7

Бренд: Ekselans Страницы: 5

Бренд: Huawei Страницы: 3

Бренд: Huawei Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды