manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

7.3

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Settings

Port Configuration (SET P) and Communication Settings

Table 7.1

Port Configuration (SET P) Settings Information 

 (Sheet 1 of 5)

Setting

Comment

Description

DEVICE

Device Type (Unused, SEL
IED, Other IED, Printer, Master).

You select the device type attached to this port:

U

nused if no device is connected.

S

EL IED if an SEL device is connected.

O

ther IED if another vendor’s IED is connected.

P

rinter if a serial printer is connected.

M

aster if an RTU, PC, PLC, NIM or ASCII terminal

is connected.

CONFIG

Auto-configure port (Y/N).

If you say yes, the SEL-2032 determines relay type, model number, 
metering capability, port ID, baud rate, passwords, relay elements, 
and other information necessary for the SEL-2032 to communicate 
automatically with SEL relays. The SEL-2032 reports the results of 
the auto-configuration once it successfully completes. This process 
may take two minutes or longer.

AUTO_BAUD

Attempt to detect port baud rate (Y/N).

The SEL-2032 depends on the IED returning a <CR> or <LF>
character in response to a <CR><LF> for baud rate determination to 
work.

PROTOCOL

Communications Type
(SEL/LMD/Modbus/DNP for Master, 
or ASCII/BINARY for Other IED).

This setting identifies special port communication parameters. For 
Other IEDs you may choose between ASCII and BINARY; selecting 
ASCII allows the normal ASCII and binary communication;
selecting BINARY automatically disables XON/XOFF handshaking.

If Port 16 DEVICE is set to master, the choices are SEL, LMD,
Modbus

®

, and DNP. If Port 12 or 14 DEVICE is master, then the 

choices are SEL, LMD, and Modbus. For any other port with 
DEVICE set to master, the choices are SEL and LMD. Selecting SEL 
allows the normal ASCII and binary communications, selecting 
LMD adds the SEL LMD Protocol, selecting Modbus disables
normal communications and enables Modbus communications on the 
selected port, and selecting DNP disables normal communications 
and enables DNP3 communications on the selected port. If you 
choose LMD, you must select an address and prefix character and set 
the settle time. If you choose Modbus, you must select the address for 
each port with Modbus data. If you choose DNP, there are a number 
of additional settings to configure the DNP3 operation. See 

Section 9: Protocols

 for reference information on LMD, Modbus, 

and DNP3 protocols.

ADDRESS

First LMD Port Address (1–81).

You supply a port address only if you selected LMD as the
PROTOCOL. The LMD address is the first of 17 used by the 
SEL-2032; the defined address is for SEL-2032 communications and 
the next 16 are for transparent communications to the respective 
ports. See 

Section 9: Protocols

 for an explanation of LMD

Distributed Port Switch Protocol.

PREFIX

LMD Address Prefix Character 
(@#$%&).

You supply LMD prefix character only if LMD was selected as the 
PROTOCOL. The prefix setting is the character the SEL-2032 
watches for when using LMD protocol. See 

Section 9: Protocols

 for 

an explanation of LMD Distributed Port Switch Protocol.

SETTLE

LMD Port Settle Time (0–30 seconds).

You supply an LMD port settle time only if LMD was selected as the 
PROTOCOL. See 

Section 9: Protocols

 for an explanation of LMD 

Distributed Port Switch Protocol.

MAP_TYPE

Modbus Map Type
(F=Float, I=Integer).

Selection for Modbus map style. See 

Section 9: Protocols

 for an 

explanation of the two map styles.

START_ID

Starting Code for ID List (0–255).

Used to offset Modbus device ID list. See 

Section 9: Protocols

 for 

reference information on Modbus.

SETTLE1

Transmission delay from RTS assertion 
(0–30000 ms).

Delay between RTS assertion and start of transmission for
Modbus and DNP3 protocols. See 

Section 9: Protocols

 for

reference information on Modbus and DNP3 protocols.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Бренд: Lantronix Страницы: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Бренд: Lantronix Страницы: 7
National Instruments SCXI-1121 User Manual preview
SCXI-1121
Бренд: National Instruments Страницы: 162
XMOS xCORE-200 Multi-channel Audio board Design Manual preview
xCORE-200 Multi-channel Audio board
Бренд: XMOS Страницы: 112
Yamaha DX7mega128 Install Manual preview
DX7mega128
Бренд: Yamaha Страницы: 6
Yamaha DX7 MiniMAX User Manual preview
DX7 MiniMAX
Бренд: Yamaha Страницы: 4
Yamaha DME Designer Setup Manual preview
DME Designer
Бренд: Yamaha Страницы: 22
Yamaha PLG100-VL Eigentümer-Handbuch preview
PLG100-VL
Бренд: Yamaha Страницы: 49
ekwb EK-FC Installation Manual preview
EK-FC
Бренд: ekwb Страницы: 2
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Бренд: IDT Страницы: 98
Moxa Technologies PT-7324 Series User Manual preview
PT-7324 Series
Бренд: Moxa Technologies Страницы: 36
Renesas Converter Board R0E521237CFK00 User Manual preview
Converter Board R0E521237CFK00
Бренд: Renesas Страницы: 6
Comelit IPNVR004BPOE Manual preview
IPNVR004BPOE
Бренд: Comelit Страницы: 19
Black Box Secure Site Manager 16 Quick Start Manual preview
Secure Site Manager 16
Бренд: Black Box Страницы: 16
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Бренд: Taiwan Commate Computer Inc. Страницы: 25
Greenlee 910FS Instruction Manual preview
910FS
Бренд: Greenlee Страницы: 52
IMC Networks Wireless Outdoor Bridge XI-1500-IH Quick Installation Manual preview
Wireless Outdoor Bridge XI-1500-IH
Бренд: IMC Networks Страницы: 13
Idis DR-8416 Quick Manual preview
DR-8416
Бренд: Idis Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды