manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

9.47

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Protocols

Distributed Network Protocol 3.0 (DNP3) LAN/WAN

As with Serial DNP3, in both the unsolicited report-by-exception and 
quiescent polling methods shown in 

Table 9.26

, you must make a selection for 

the session’s PUNSL

nn

 setting. This setting enables or disables unsolicited 

data reporting at power up for this session. If your master can send the DNP3 
message to enable unsolicited reporting from the SEL-2032, you should set 
the session’s PUNSL

nn

 to No.

Device Profile 
Document

Table 9.27

 contains the standard DNP3 over Ethernet device profile 

information. Rather than checkboxes in the example Device Profile in the 
DNP3 Subset Definitions, only the relevant selections are shown.

Unsolicited report-by-
exception

The slave devices send 
unsolicited event data to the 
master and the master occa-
sionally sends integrity 
polls for static data.

Set ECLASSB, ECLASSC, 
ECLASSA to the desired non-
zero event class, set UNSL

nn

 

to Yes and PUNSL

nn

 to Yes or 

No.

Quiescent

The master never polls and 
relies on unsolicited reports 
only.

Set ECLASSB, ECLASSC, 
ECLASSA to the desired non-
zero event class, set UNSL

nn

 

and PUNSL

nn

 to Yes.

Table 9.26

DNP3 Over Ethernet Access Methods 

 (Sheet 2 of 2)

Access Method

Master Polling

SEL-2032/SEL-2701 

Settings

Table 9.27

SEL-2032 DNP3 Over Ethernet Device Profile 

 (Sheet 1 of 2)

Parameter

Value

Vendor name

Schweitzer Engineering Laboratories

Device name 

SEL-2032 Communications Processor with 
SEL-2701 Ethernet Processor

Highest DNP3 request level

Level 2

Highest DNP3 response level 

Level 2

Device function

Slave

Notable objects, functions, 
and/or qualifiers supported

None

Maximum data link 
frame size transmitted/received (octets)

292

Maximum data link retries

0

Requires data link layer confirmation

Never

Maximum application fragment 
size transmitted/received (octets)

2048

Maximum application layer retries

None

Requires application layer confirmation

When reporting Event Data

Data link confirm time-out

Configurable

Complete application fragment time-out

None

Application confirm time-out

Configurable

Complete Application response time-out

None

Executes control WRITE binary outputs

Always

Executes control SELECT/OPERATE

Always

Executes control DIRECT OPERATE

Always

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

dbx ProVocal Specifications preview
ProVocal
Бренд: dbx Страницы: 2
Garmin GND 10 Installation Instructions preview
GND 10
Бренд: Garmin Страницы: 2
ICP DAS USA ET-7000 series Quick Start Manual preview
ET-7000 series
Бренд: ICP DAS USA Страницы: 14
ICP DAS USA I-2533 User Manual preview
I-2533
Бренд: ICP DAS USA Страницы: 25
ICP DAS USA ET-2200 Series Manual preview
ET-2200 Series
Бренд: ICP DAS USA Страницы: 15
ICP DAS USA PCIe-S112 Quick Start Manual preview
PCIe-S112
Бренд: ICP DAS USA Страницы: 8
Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Бренд: Jetter Страницы: 35
Patton electronics 1084 Installation And Operation Manual preview
1084
Бренд: Patton electronics Страницы: 16
Avaya PARTNER PC CARD Installation Instructions preview
PARTNER PC CARD
Бренд: Avaya Страницы: 4
S&T kontron KBox E-420-R1K/V1K User Manual preview
kontron KBox E-420-R1K/V1K
Бренд: S&T Страницы: 82
Optostar OP-8000-EDFA-1U Series Manual preview
OP-8000-EDFA-1U Series
Бренд: Optostar Страницы: 9
ZALMAN CNPS12X User Manual preview
CNPS12X
Бренд: ZALMAN Страницы: 11
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Бренд: AOpen Страницы: 18
NCR 7702-K134 Upgrade Manual preview
7702-K134
Бренд: NCR Страницы: 15
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Бренд: swiftech Страницы: 2
AXIOMTEK UST510-52B-FL Series User Manual preview
UST510-52B-FL Series
Бренд: AXIOMTEK Страницы: 77
Allen-Bradley SLC 5/03 Installation Instructions Manual preview
SLC 5/03
Бренд: Allen-Bradley Страницы: 76
ICP DAS USA VEX-112 Quick Start Manual preview
VEX-112
Бренд: ICP DAS USA Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды