manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

2.2

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Installation

Jumper Settings

Input/Output 
Connections

If your SEL-2032 is equipped with the optional I/O board, it has a terminal 
strip that extends nearly the full width of the SEL-2032, near the top of the 
rear panel.

Configure the Inputs for 24 V, 48 V, 125 V, or 250 V

The selection of input operating range is made at ordering time and cannot be 
modified by the user. The inputs on the SEL-2032 are level-sensitive; they will 
not operate if the input is inadvertently grounded.

Configure the Output Contact Form

The SEL-2032 I/O board is shipped from the factory with Form A output 
contacts. You may reconfigure the contacts by desoldering and then 
resoldering the 20 AWG jumper wire for each contact. 

Table 2.2

 and 

Figure 2.5

 show the jumper positions required to configure the contacts.

 

Access and Set 
Internal Jumpers

After you have decided on the appropriate SEL-2032 hardware configuration, 
you are ready to reconfigure the SEL-2032 if the default configuration does 
not meet your needs. Perform the following steps to gain access to internal 
jumpers:

DANGER:

 Disconnect or 

de-energize all external 

connections before opening this 
device. Contact with hazardous 
voltages and currents inside this 
device can cause electrical shock 
resulting in injury or death.

!

Step 1. Disconnect power from the SEL-2032.

Step 2. Remove the screws attaching the front panel and remove the 

front panel.

Step 3. If the optional I/O board is installed, disconnect any cables 

joining the I/O board to the main board and disconnect the 
power cable from the SEL-2032 main board. Disconnect any 
cables connected to the rear of the SEL-2032.

CAUTION:

 Equipment 

components are sensitive to 

electrostatic discharge (ESD). 
Undetectable permanent damage 
can result if you do not use proper 
ESD procedures. Ground yourself, 
your work surface, and this 
equipment before removing any 
cover from this equipment. If your 
facility is not equipped to work with 
these components, contact SEL 
about returning this device and 
related SEL equipment for service.

!

Step 4. Remove the main board by sliding it out. Remove the I/O board 

by sliding it out.

Step 5. Configure main board jumpers according to the options given 

in 

Table 2.1

.

See 

Figure 2.4

 for main board jumper locations.

Step 6. Configure I/O board jumpers according to the options given in 

Table 2.2

.

See 

Figure 2.5

 for I/O board jumper locations.

Table 2.2

Optional I/O Board Contact Form Jumper Positions

Output

Contact

Jumper

Jumper Setting

Form A contact 

Form B contact

OUT1
OUT2
OUT3
OUT4

JMP36
JMP35
JMP34
JMP33

Connect A to Common with 
20 AWG wire (factory setting)

Connect B to
Common with 20 AWG wire

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 5
National Instruments USB-6501 Quick Start preview
USB-6501
Бренд: National Instruments Страницы: 5
National Instruments PXIe-8106 User Manual preview
PXIe-8106
Бренд: National Instruments Страницы: 76
Maxim MAX1415 Specification Sheet preview
MAX1415
Бренд: Maxim Страницы: 14
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Бренд: ZALMAN Страницы: 9
NEC Thin Client US310e Getting Started preview
Thin Client US310e
Бренд: NEC Страницы: 6
Grundig GSS STC 160 Assembly Instruction Manual preview
GSS STC 160
Бренд: Grundig Страницы: 24
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Бренд: Buffalo Страницы: 71
MEDIATEK MT6252 Design Manual preview
MT6252
Бренд: MEDIATEK Страницы: 166
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Бренд: ZoneVu Страницы: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Бренд: FUNcube Страницы: 23
Navitar 1-62643 Dimensional Drawing preview
1-62643
Бренд: Navitar Страницы: 1
Disc Makers ElitePro User Manual preview
ElitePro
Бренд: Disc Makers Страницы: 12
KEB 1MF5280-7008 Instruction Manual preview
1MF5280-7008
Бренд: KEB Страницы: 32
Curtiss-Wright GTS/DEC/003 Manual preview
GTS/DEC/003
Бренд: Curtiss-Wright Страницы: 10
Curtiss-Wright DUCOR-80-40-00 User Manual preview
DUCOR-80-40-00
Бренд: Curtiss-Wright Страницы: 59
Cambium Networks ePMP Elevate Quick Start Manual preview
ePMP Elevate
Бренд: Cambium Networks Страницы: 7
KTI Networks KGS-2421 Installation Manual preview
KGS-2421
Бренд: KTI Networks Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды