manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

SEL-2032 Communications Processor

Instruction Manual

Date Code 20120126

Equipment components are sensitive to electrostatic discharge 
(ESD). Undetectable permanent damage can result if you do 
not use proper ESD procedures. Ground yourself, your work 
surface, and this equipment before removing any cover from 
this equipment. If your facility is not equipped to work with 
these components, contact SEL about returning this device and 
related SEL equipment for service.

!

CAUTION

There is danger of explosion if the battery is incorrectly 
replaced.  Replace only with Ray-O-Vac

®

 no. BR2335 or 

equivalent recommended by manufacturer.  Dispose of used 
batteries according to the manufacturer’s instructions.

!

CAUTION

Have only qualified personnel service this equipment. If you are 
not qualified to service this equipment, you can injure yourself 
or others, or cause equipment damage.

!

WARNING

This device is shipped with default passwords. Default 
passwords should be changed to private passwords at 
installation. Failure to change each default password to a 
private password may allow unauthorized access. SEL shall not 
be responsible for any damage resulting from unauthorized 
access.

!

WARNING

Disconnect or de-energize all external connections before 
opening this device. Contact with hazardous voltages and 
currents inside this device can cause electrical shock resulting 
in injury or death.

!

DANGER

Contact with instrument terminals can cause electrical shock 
that can result in injury or death.

!

DANGER

 Les composants de cet équipement sont sensibles aux 
décharges électrostatiques (DES). Des dommages permanents 
non-décelables peuvent résulter de l’absence de précautions 
contre les DES. Raccordez-vous correctement à la terre, ainsi 
que la surface de travail et l’appareil avant d’en retirer un 
panneau. Si vous n’êtes pas équipés pour travailler avec ce type 
de composants, contacter SEL afin de retourner l’appareil pour 
un service en usine.

!

ATTENTION

Il y a un danger d’explosion si la pile électrique n’est pas 
correctement remplacée.  Utiliser exclusivement Ray-O-Vac® 
No. BR2335 ou un équivalent recommandé par le fabricant.  Se 
débarrasser des piles usagées suivant les instructions du 
fabricant.

!

ATTENTION

Seules des personnes qualifiées peuvent travailler sur cet 
appareil. Si vous n’êtes pas qualifiés pour ce travail, vous 
pourriez vous blesser avec d’autres personnes ou endommager 
l’équipement.

!

AVERTISSEMENT

Cet appareil est expédié avec des mots de passe par défaut. A 
l’installation, les mots de passe par défaut devront être 
changés pour des mots de passe confidentiels. Dans le cas 
contraire, un accés non-autorisé á l’équipement peut être 
possible. SEL décline toute responsabilité pour tout dommage 
résultant de cet accés non-autorisé.

!

AVERTISSEMENT

Débrancher tous les raccordements externes avant d’ouvrir cet 
appareil. Tout contact avec des tensions ou courants internes à 
l’appareil peut causer un choc électrique pouvant entraîner des 
blessures ou la mort.

!

DANGER

Tout contact avec les bornes de l’appareil peut causer un choc 
électrique pouvant entraîner des blessures ou la mort.

!

DANGER

© 2003–2012 by Schweitzer Engineering Laboratories, Inc. All rights reserved.

All brand or product names appearing in this document are the trademark or registered trademark of their respective holders. No SEL 
trademarks may be used without written permission. SEL products appearing in this document may be covered by US and Foreign patents.

Schweitzer Engineering Laboratories, Inc. reserves all rights and benefits afforded under federal and international copyright and patent laws in 
its products, including without limitation software, firmware, and documentation.

The information in this manual is provided for informational use only and is subject to change without notice. Schweitzer Engineering 
Laboratories, Inc. has approved only the English language manual.

This product is covered by the standard SEL 10-year warranty. For warranty details, visit www.selinc.com or contact your customer service 
representative.

PM2032-01

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

F5 WANJet 500 Quick Start Card preview
WANJet 500
Бренд: F5 Страницы: 2
F5 ARX-500 Hardware Reference Manual preview
ARX-500
Бренд: F5 Страницы: 90
F5 ARX-4000 Parts Replacement Manual preview
ARX-4000
Бренд: F5 Страницы: 47
Xilica Audio Design neutrino series Quick Start Manual preview
neutrino series
Бренд: Xilica Audio Design Страницы: 26
Dahua Smart 1U Quick Start Manual preview
Smart 1U
Бренд: Dahua Страницы: 24
Lanner NCA-2510 Installation Manual preview
NCA-2510
Бренд: Lanner Страницы: 2
NEC P401-TMX4D User Manual preview
P401-TMX4D
Бренд: NEC Страницы: 2
u-blox ANT-B10 User Manual preview
ANT-B10
Бренд: u-blox Страницы: 29
Seattle Computer Products 8086 CPU Instruction Manual preview
8086 CPU
Бренд: Seattle Computer Products Страницы: 31
Adaptec AAA-130SA SERIES Installation And Hardware Manual preview
AAA-130SA SERIES
Бренд: Adaptec Страницы: 94
A4Tech RH-10 User Manual preview
RH-10
Бренд: A4Tech Страницы: 8
ZALMAN CNPS7000A Series User Manual preview
CNPS7000A Series
Бренд: ZALMAN Страницы: 9
Idis DR-6316PS-S Quick Manual preview
DR-6316PS-S
Бренд: Idis Страницы: 16
ZIMO MXULFA Instruction Manual preview
MXULFA
Бренд: ZIMO Страницы: 13
ADS Technologies API-800 Installation Manual preview
API-800
Бренд: ADS Technologies Страницы: 21
Aaeon GENE-EHL7 User Manual preview
GENE-EHL7
Бренд: Aaeon Страницы: 119
Netopia D3100-I User Reference Manual preview
D3100-I
Бренд: Netopia Страницы: 138
Quatech SSPX-100 User Manual preview
SSPX-100
Бренд: Quatech Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды