manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

9.3

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Protocols

SEL Fast Message Protocol

the manual trip and close settings (BK1MTR, BK2MTR, BK1MCL, 
BK2MCL) in the SEL-421. Operation for circuit breaker two with BR2, OC2, 
and CC2 is similar.

The example 

AUTO

 command also shows that SER support for binary 

unsolicited or Fast SER messages is available. This means that messages are 
automatically generated by the relay SER (sequential events recorder) that 
send the new status of selected Relay Word bits and the timestamp associated 
with the change of state. If you enable Fast SER, you can collect the station 
SER information from an SEL-2032 port using SEL protocol and the SEL PC 
driver software or from DNP3 messages from the SEL-2032.

The supported commands that are listed describe what data you can collect 
from the relay using “20” messages rather than writing individual data 
collection messages and configuring the SEL-2032 to parse the data. For 
example, you can collect instantaneous metering data by setting the SEL-2032 
to send a 20METER message in the automatic messaging settings (SET A). 
When you enter 20METER as the outgoing message, you will not be 
prompted for any further configuration because the SEL-2032 has already 
collected the necessary information to send the message and parse the results 
during the auto-configuration process.

Sequential Events 
Recorder (SER) 
Data

The SEL-2032 is capable of collecting Sequential Events Recorder (SER) data 
from SEL relays, generating SER data based on its 16 digital inputs, and 
automatically forwarding all SER data to another SEL-2032 or other 
programmable data gathering device. SER data collection from connected 
devices requires that REC_SER=Y and a TARGET data region is set up on 
each port that will receive the data. All SER data is collected and transmitted 
with the SEL Fast Message protocol.

If you have a Master device, capable of capturing and translating data, you 
must follow these steps to perform SER data collection:

NOTE:

 SER data are also available to 

other processes within the SEL-2032. 
When a port is enabled to receive SER 
information from the relay, the 
SEL-2032 uses Data region 8 (D8) as 
the SER region (see 

Data Regions on 

page 6.20

).

Step 1. Use 

SET P 

n

 to auto-configure all relay ports. 

Step 2. After auto-configuration, use the 

AUTO 

n

 command to 

determine the capability of the connected relay.

Not all SEL relays support the Fast Message protocol for 
collecting SER data. If the relay supports the Fast Message 
protocol, you should see the line 

SER Support: Binary 

Unsolicited

 in the 

AUTO

 command response. If this line is not 

present, then the REC_SER setting has no affect and the 
SEL-2032 cannot perform automatic SER collection from the 
relay.

You may wish to connect one or more relay digital outputs to 
the digital inputs of the SEL-2032 and monitor the SEL-2032 
input elements as SER data.

Step 3. Use 

SET A 

n

 

to enable gathering of SER data and set up a 

TARGET data region on all ports 

n

. For each port 

n

, set 

REC_SER = Y and add a “20TARGET” auto-message with any 
real or “dummy” trigger. If you do not actually want to collect 
TARGET data, you may use a dummy trigger for the auto-
message as shown below.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Harmonic XOS User Manual preview
XOS
Бренд: Harmonic Страницы: 56
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Бренд: RadiSys Страницы: 44
IAR SYSTEMS IAR KickStart Kit TWR-K60N512-IAR Getting Started Manual preview
IAR KickStart Kit TWR-K60N512-IAR
Бренд: IAR SYSTEMS Страницы: 8
AXIOMTEK AIE900-XNX Series User Manual preview
AIE900-XNX Series
Бренд: AXIOMTEK Страницы: 53
Rabbit RabbitCore RCM4400W Product Manual preview
RabbitCore RCM4400W
Бренд: Rabbit Страницы: 126
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Бренд: Zhone Страницы: 114
Grundig GSS STC 160 Assembly Instruction Manual preview
GSS STC 160
Бренд: Grundig Страницы: 24
pivotal COMMWARE ECHO 5G How To Set Up preview
COMMWARE ECHO 5G
Бренд: pivotal Страницы: 2
NC-link NC-AP111 User Manual preview
NC-AP111
Бренд: NC-link Страницы: 20
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Бренд: Lutron Electronics Страницы: 4
LaCie FireWire 800 ExpressCard 34 Quick Install Manual preview
FireWire 800 ExpressCard 34
Бренд: LaCie Страницы: 24
IBM Power System S914 Installing Instructions preview
Power System S914
Бренд: IBM Страницы: 48
Xcellon DRD-501 User Manual preview
DRD-501
Бренд: Xcellon Страницы: 24
Barracuda CloudGen Firewall Revision preview
CloudGen Firewall
Бренд: Barracuda Страницы: 8
Delta AH10EN-5A Series Operation Manual preview
AH10EN-5A Series
Бренд: Delta Страницы: 132
Ross ULTRIX-FM-NS-1RU Install Manual preview
ULTRIX-FM-NS-1RU
Бренд: Ross Страницы: 5
ZALMAN CNPS9500 AT User Manual preview
CNPS9500 AT
Бренд: ZALMAN Страницы: 9
I-Tech NW117HD-8Ke User Manual preview
NW117HD-8Ke
Бренд: I-Tech Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды