manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

1.14

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Introduction and Specifications

Functions

Synchronizing Time Source

.

The SEL-2032 distributes a demodulated 

IRIG-B signal through Ports 1–16. This signal can be used by any 
attached device that recognizes the IRIG-B code by connecting the 
proper cable to the SEL-2032. The signal can be distributed to SEL 
relays that accept IRIG-B input, by using a special cable designed for 
both communication and IRIG-B signals. The SEL-2032 internally 
generates the IRIG-B signal, unless you connect an external source of 
modulated or demodulated IRIG-B to the SEL-2032. You can also 
perform low-accuracy time synchronization of the SEL-2032 using a 
serial protocol or an installed protocol card. See your protocol card 
instruction manual for details. If the connected device does not accept 
IRIG-B, you can program the SEL-2032 to send a date and time 
message to the device.

Communications 
Processor

The SEL-2032 has a distinct and significant advantage over simple port 
switches because of its sophisticated and powerful communications 
processing capabilities. 

Figure 1.7

 shows a typical application that includes 

several of the communication processing types described below. 

Table 1.1

 

describes the communications on each type of link shown in 

Figure 1.7

.

Figure 1.7

SEL-2032 Manages Communications With Multiple Master and 

Slave Devices

Table 1.1

Communications Type

From

To

Description

IED

SEL-2032

Messages That Emulate Native IED Protocol

SEL IED

SEL-2032

Autoconfiguration, SEL “20” Messages

Modem

SEL-2032

SEL-2032 Command Set, User-Defined Messages

RTU or SCADA Master

SEL-2032

DNP3 Slave Level 2 or Modbus

Local HMI

SEL-2032

Ethernet High-Speed Network

GPS Clock

SEL-2032

IRIG-B Time Synchronization

SEL-2032

RTU or 
SCADA Master

Modem

GPS Clock

Satellite

Local HMI

IED

SEL IED

SEL IED

SEL IED

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Бренд: Cabletron Systems Страницы: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Бренд: Cabletron Systems Страницы: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Бренд: Cabletron Systems Страницы: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Бренд: Cabletron Systems Страницы: 2
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Бренд: Cabletron Systems Страницы: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Бренд: Cabletron Systems Страницы: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Бренд: Cabletron Systems Страницы: 60
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Бренд: Cabletron Systems Страницы: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Бренд: Cabletron Systems Страницы: 4
National Instruments NI 9426 Getting Started Manual preview
NI 9426
Бренд: National Instruments Страницы: 17
National Instruments Fieldpoint cFP-RTD-124 Operating Instructions Manual preview
Fieldpoint cFP-RTD-124
Бренд: National Instruments Страницы: 15
Matrox Millennium P650 User Manual preview
Millennium P650
Бренд: Matrox Страницы: 54
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Бренд: Grizzly Страницы: 9
EZCast Pro Dongle II User Manual preview
Pro Dongle II
Бренд: EZCast Страницы: 24
Lanner NCA-6520 User Manual preview
NCA-6520
Бренд: Lanner Страницы: 141
ZyXEL Communications GS1900 Series User Manual preview
GS1900 Series
Бренд: ZyXEL Communications Страницы: 263
Kontron PC/104-PCMCIA-1 User Manual preview
PC/104-PCMCIA-1
Бренд: Kontron Страницы: 20
NovaStar Nova M3 MFN300 Operation Manual preview
Nova M3 MFN300
Бренд: NovaStar Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды