manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

2.18

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Installation

Getting Started

*>>

AUTO 2 <Enter>

FID:       FID=SEL-351S-7-R106-V0-Z003003-D20010110
DEVICE ID: FEEDER 1
BAUD RATE: 19200
OPERATE SUPPORT: Binary (1 Breakers, 16 Remote Bits S-C-P)
LEVEL 1 PASSWORD: OTTER
COMMANDS SUPPORTED:
  B 20METER
  B 20DEMAND
  B 20TARGET
  A 20HISTORY
  A 20STATUS
  A 20EVENT
  A 20EVENTS
  A 20EVENTL

*>>

Figure 2.9

AUTO 2 Command Displays Fast Message Features

Step 5. Enter the 

Port 2

 command to establish a transparent connection 

to the relay. Press 

<Enter>

 and verify that you receive an equal 

sign (=) relay prompt.

Step 6. Enter the 

ACCESS

 and 

2 ACCESS

 command to enter Access 

Level 2 on the SEL-351S. The default passwords for the 
SEL-351S are the same as the SEL-2032.

Step 7. Enter the 

SET P

 command and change the SPEED setting to 

19200 bits per second. When you enter 

Y

 to save changes, you 

will lose communication with the relay. This changes the baud 
rate for the relay.

Step 8. Press 

<Ctrl+D>

 to end the transparent connection to the relay.

Step 9. Use the 

SET P 2

 command to change the baud rate on Port 2 of 

the SEL-2032 to 19200 bits per second.

Step 10. Next, issue the command 

SET A 2

 to set an auto-message to 

collect relay meter and target data. 

➢

Press 

<Enter>

 to respond to prompts about saving 

unsolicited messages (

AUTOBUF

), the startup string 

(

STARTUP

), operate command enable (

SENDOPER

), 

and receive SER enable (

RECSER

).

➢

Enter 

2

 when prompted for the message count. 

➢

At the ISSUE1 prompt, enter 

P00:00:01

 to set the 

message to trigger once every second.

➢

At the MESG1 prompt, enter 

20METER

 to send the 

request for meter data to the SEL relay.

➢

At the ISSUE2 prompt, enter 

P00:00:01

 and at the 

MESG2 prompt enter 

20TARGET

 to collect relay 

target data.

➢

Type 

END <Enter>

 to accept the default for remaining 

settings and 

Y <Enter>

 to save changes.

As soon as the SEL-2032 accepts the setting change, the TXD 
and RXD Port 2 LEDs on the SEL-2032 begin to flash as the 
SEL-2032 requests and receives meter data every second. 

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Samsung AllShare Cast Dongle Quick Start Manual preview
AllShare Cast Dongle
Бренд: Samsung Страницы: 2
D-Link DSL-2750U Setup preview
DSL-2750U
Бренд: D-Link Страницы: 14
Measurement Computing PC-CARD DAS16 User Manual preview
PC-CARD DAS16
Бренд: Measurement Computing Страницы: 27
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Бренд: IDT Страницы: 11
TDK HHM Series HHM2411 Specification Sheet preview
HHM Series HHM2411
Бренд: TDK Страницы: 2
ZALMAN CNPS7000A Series User Manual preview
CNPS7000A Series
Бренд: ZALMAN Страницы: 9
INNOSILICON T3-43T User Manual preview
T3-43T
Бренд: INNOSILICON Страницы: 11
NZXT RESPIRE T40 Manual preview
RESPIRE T40
Бренд: NZXT Страницы: 2
Beckhoff EK1122 Documentation preview
EK1122
Бренд: Beckhoff Страницы: 84
Intel G6950 Documentation Update preview
G6950
Бренд: Intel Страницы: 51
TECO e-chill 1 Instruction Manual preview
e-chill 1
Бренд: TECO Страницы: 24
Roland Session SR-JV80-09 Owner'S Manual preview
Session SR-JV80-09
Бренд: Roland Страницы: 8
IEI Technology IMBA-C604EP User Manual preview
IMBA-C604EP
Бренд: IEI Technology Страницы: 213
WATT & WELL SECC Series Getting Started preview
SECC Series
Бренд: WATT & WELL Страницы: 15
Thermaltake CLP0539 Installation Manual preview
CLP0539
Бренд: Thermaltake Страницы: 1
Cambium Networks PTP 820C HP Installation Manual preview
PTP 820C HP
Бренд: Cambium Networks Страницы: 227
StarTech.com S32M2NGFFPEX Instruction Manual preview
S32M2NGFFPEX
Бренд: StarTech.com Страницы: 16
AVYCON AVK-HN41V4-1T-NVR Quick Start Manual preview
AVK-HN41V4-1T-NVR
Бренд: AVYCON Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды